Avaya J100 Series Скачать руководство пользователя страница 43

Страница: 43 / 528

Broadworks topology without SBC

Network Server

Application Server 2

Application Server 1

XSP (Xtended Services Platform)

Media Gateway

MSBR (Multi-Service Business Router)

Related links

Open SIP operation modes

on page 40

Broadsoft Device Management

With the Broadsoft Device Management feature, you can download device-specific configuration

files from the Broadsoft server in Avaya J100 Series IP Phones. The phone does not require an

Open SIP provisioning server and connects automatically to the Broadsoft server.

Avaya J100 Series IP Phones support the following types of Broadsoft Device Management

authentication:

• MAC-based authentication.
• HTTP digest authentication.
• TLS mutual authentication.

Device management configuration

The following initial configuration parameters should be set for the Broadsoft Device Management:

Broadsoft configuration

April 2020

Installing and Administering Avaya J100 series IP Phones in an Open SIP

environment

Comments on this document? [email protected]

Содержание J100 Series

















































































































































































































































































































































































































































































































































Результаты поиска

Содержание J100 Series

Отзывы:

Avaya J100 Series, Установка и администрирование, Страница: 43 / 528

Результаты поиска

Содержание J100 Series

Отзывы: