Avaya J100 Series Скачать руководство пользователя страница 168

Страница: 168 / 528

Name

Description

Exchange Server Secure Mode

Specifies the exchange server mode.

The options are:

•

HTTP

•

HTTPS (default)

Configuring Multicast Paging

About this task

Use this procedure to enable or disable Multicast Paging on the phone and configure the settings

for transmission.

Procedure

1. Log in to the web interface as an administrator.

2. In the navigation pane, click

Multicast Paging

3. In the Multicast Paging tab, configure the following fields:

•

Multicast Paging State

•

Multicast Paging Codec

4. Configure the incoming and outgoing paging groups in the following sections:

• Multicast Paging Groups To Listen

• Multicast Paging Groups To Send

5. Click one of the following:

•

Save

: To save the changes.

•

Reset to Default

: To revert to the default values.

Related links

Multicast Paging

on page 233

Multicast Paging configuration

on page 234

Phone configuration

April 2020

Installing and Administering Avaya J100 series IP Phones in an Open SIP

environment

168

Comments on this document? [email protected]

Содержание J100 Series

















































































































































































































































































































































































































































































































































Результаты поиска

Содержание J100 Series

Отзывы:

Avaya J100 Series, Установка и администрирование, Страница: 168 / 528

Результаты поиска

Содержание J100 Series

Отзывы: