Avaya J100 Series Скачать руководство пользователя страница 106

Страница: 106 / 528

Name

Description

Signaling Keep Alive Interval

Specifies the interval, in seconds, between keep-
alives used to refresh NAT bindings for the phone
signaling IP address and port.

Valid values:

• None: The phone will use the default value.

• 15 – 900: The phone will use this value as the

keep-alive interval for every SIP registration and
dialog.

The default value is 15.

Configuring Ethernet settings

About this task

When you click on any configuration field, the screen displays the details of that field in the

Parameter Help section.

Procedure

1. Log in to the web interface as an administrator.

2. In the navigation pane, click

Ethernet

3. Configure the following areas:

• IP Configuration

• IPv4 Configuration

• IPv6 Configuration

• 802.1X Supplicant Operating Mode

• VLAN

• QoS

• LLDP

• Ethernet Interface

4. Click one of the following:

•

Save

: To save the configuration changes.

•

Reset to Default

: To revert to the default values.

Phone configuration

April 2020

Installing and Administering Avaya J100 series IP Phones in an Open SIP

environment

106

Comments on this document? [email protected]

Содержание J100 Series

















































































































































































































































































































































































































































































































































Результаты поиска

Содержание J100 Series

Отзывы:

Avaya J100 Series, Установка и администрирование, Страница: 106 / 528

Результаты поиска

Содержание J100 Series

Отзывы: