Avaya INDeX 30 Скачать руководство пользователя страница 50 | Manualshive

Страница: 50 / 53

Avaya INDeX 30 Скачать руководство пользователя страница 50

Regulatory Instructions for Use

INDeX Operation in United Kingdom - Page 50

Installation & Maintenance

Regulatory Instructions for Use - Page 50

INDeX 30

38DHB0002UKDF- Issue 4 (07/2001)

Regulatory Instructions for Use

INDeX Operation in United Kingdom

1) 999 and 112 calls must not be barred. Doing so will invalidate BABT approval.
2) Simple Call Routing Mode (SCRM) lines must be identified separately from the

non-SCRM lines (loop start disconnect clearing & guarded clearing) at the MDF.

3) PSTN lines must be segregated from non-PSTN lines and their connection strips

shall be suitably labelled.

4) All connections at the MDF shall be identifiable by suitable labelling.
5) The CE mark displayed on INDeX equipment indicates the systems compliance

with the European EMC LV, and R&TTE directive and common technical

regulations for Primary Rate and Basic Rate ISDN.

6) All ports for the connection of other non-telecommunications apparatus have a

Safety Extra Low Voltage (SELV) safety status.

INDeX Operation in Australia

1) 000 emergency calls must not be barred. Doing so will invalidate the approval to

TS031 and TS038.

2) When connecting to a TS013 ISDN Basic Rate Interface, only Point to Multi-

Point to operation shall be configured.

3) When connecting to a TS013 ISDN Basic Rate Interface only terminals that

comply with TS013 may be connected to the BRI ’S’ ports as the bearer

capability is passed through the switch

4) As the INDeX does not support emergency dialling after loss of power, the

following warning notice should be recognised:

WARNING

This equipment will be inoperable when mains power fails.

INDeX Operation in Finland

To comply with the safety regulations for Finland, the INDeX Cabinet must be

connected to a safety earth as follows:

WARNING

Attach earth lead to cabinet with a suitable M6 bolt/screw in

threaded insert provided adjacent to mains input socket on the

left hand side of cabinet (facing to the front).

The earth lead and connections

are not

provided by Avaya.

INDeX Operation in Singapore

To comply with the safety regulations for Singapore, the INDeX Cabinet must be

connected to a safety earth as follows:

WARNING

Attach earth lead to cabinet with a suitable M6 bolt/screw in

threaded insert provided adjacent to mains input socket on the

left hand side of cabinet (facing to the front).

The earth lead and connections

are not

provided by Avaya.

«
...
48
49
50
51
52
...
»

Содержание INDeX 30






















































Отзывы:

Нет отзывов