manualshive.com logo in svg

Avaya G700, Установка и обновление, Страница: 641 / 808

Поделиться
Скачать
Avaya G700 Скачать руководство пользователя страница 641

On-site Preparation for the Upgrade

Issue 10.2 May 2007

641

 

Note:

Note:

Be sure to reset alarm origination after the upgrade.

3. Type 

almenable

 (without any options) to verify the alarm origination status. 

You should see:

incoming: enable

Dial Out Alarm Origination: neither

SNMP Alarm Origination: n

Saving a copy of the 4600-series phone configuration file, if any

During an upgrade, any data in the /tftpboot directory is overwritten with new software and 
firmware. If the system was using the http or tftp capability for 4600-series phone firmware 
downloads and configuration updates, the firmware and 4600-series phone configuration file 
are overwritten. 

You must redownload the 46xx firmware file after the upgrade. However, you can save a copy of 
the 46xx configuration file 

before 

the upgrade and copy it back into the /tftpboot directory 

after

 

the upgrade.

To copy the 4600-series configuration file to a safe location, perform the following steps:

1. Access the server’s command line interface using telnet and an IP address of 

192.11.13.6

.

2. Log in as 

craft

.

3. At the Linux command line, type 

cd /tftpboot

, and press 

Enter

.

4. At the prompt, type 

ls 46*

, and press 

Enter

.

If a named 

46xxsettings.txt 

may appear in the list, or the prompt may reappear with no 

files listed. If the file name does not appear, there is no file to copy. You are finished with this 
procedure.

5. If the file name 

46xxsettings.txt 

appears,at the Linux command line, type 

cp 

46xxsettings.txt ~ftp/pub

 .

The 4600-series phone settings file is now in a protected directory, /var/home/ftp/pub, and 
will not be overwritten during the upgrade. You will copy this file back to the /tftpboot 
directory after the upgrade.

Содержание G700









































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов