manualshive.com logo in svg

Avaya G700, Установка и обновление, Страница: 540 / 808

Поделиться
Скачать
Avaya G700 Скачать руководство пользователя страница 540

Manual upgrade of an S8300A and G700 to R4.0

540 Installing and Upgrading the Avaya G700 Media Gateway and Avaya S8300 Media Server

 

The steps to upgrade an S8300 configured as an LSP are the same as the steps to upgrade an 
S8300 configured as the primary controller, with the following additional considerations:

●

The version of Communication Manager running on the LSP must be the same as, or later 
than, the version running on the primary controller.

●

If upgrading both the primary controller and the LSP, the LSP must be upgraded first. 
Then, with Communication Manager turned off on the LSP, the primary controller is 
upgraded.

●

Do not save translations on an LSP.

!

CAUTION:

CAUTION:

These upgrade procedures require remastering the hard drive on the S8300B or 
S8300C. This can result in a service interruption of 3–4 hours, or up to 6 hours if 
IA770 is being used.

Tip:

Tip:

You may skip some of the procedures described in this chapter depending on the 
upgrade scenario. Watch for the 

skip to

 instructions. 

Issues for IA770 INTUITY AUDIX on Release 1.3 or earlier on an
S8300A Media Server

!

CAUTION:

CAUTION:

Communication Manager Release 4.0 does not support the CWY1 integration of 
IA770 INTUITY AUDIX Messaging. As a result, if the S8300 Media Server uses a 
CWY1 board to integrate the IA770 INTUITY AUDIX application, you must 
remove the current IA770 integration administration before the upgrade and then 
administer the integration to H.323 after the upgrade. 

For an upgrade of Communication Manager from Release 1.3 or earlier on an S8300A, the 
customer must save IA770 administrative data to Mailbox Manager, ASA, or another tool, and 
restore that data after the upgrade to release 4.0. If administrative data is not saved in another 
tool, the customer must readminister IA770 INTUITY AUDIX Messaging after the upgrade. 
Additionally, all names, custom announcements, and messages are lost. Subscribers who use 
Message Manager should be encouraged to save messages to their personal computers and 
restore them after the upgrade.

Содержание G700









































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов