Avaya ERS 8600 series Скачать руководство пользователя | Manualshive

Страница: 403 / 420

background image

Basic OSPF information about a port

Use the

show ports statistics ospf main

command to display basic OSPF

information about the specified port or for all ports. The syntax for this command is as follows.

show ports statistics ospf main

<ports>

The following table explains parameters for this command.

Table 45: Command parameters

Parameter

Description

<ports>

Specifies the port or range of ports
configured in the format slot/port.

Extended OSPF information

Use the

show routing statistics interface

command to display extended OSPF

information about the specified port or for all ports. The syntax for this command is as follows.

show routing statistics interface <interface> [slot/port]

The following table explains the parameters for this command.

Table 46: Command parameters

Parameter

Description

interface

Specifies the interface type for which to
report statistics. The options include
fastethernet and gigabitEthernet.

slot/port

Specifies a particular slot and port or list of
ports for which to provide results. If you omit
a specific port or port list, results include all
ports on the interface type.

The following figure shows sample output for this command.

Basic OSPF information about a port

Configuration — IPv6 Routing

November 2010 403

«
...
401
402
403
404
405
...
»

Содержание ERS 8600 series





































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ERS 8600 series

Бренд: D-Link Страницы: 99

Бренд: D-Link Страницы: 5

Бренд: D-Link Страницы: 15

AirPro DWL-6000AP

Бренд: D-Link Страницы: 65

Бренд: H3C Страницы: 1057

Бренд: 2N Страницы: 11

Бренд: 2N Страницы: 5

Бренд: 2N Telekomunikace Страницы: 24

Бренд: Axis Страницы: 104

Бренд: Netis Страницы: 16

Бренд: ICP DAS USA Страницы: 62

Бренд: Paradyne Страницы: 6

Бренд: Hunter Страницы: 2

NetVanta Serial Dial Backup Interface Module (DIM) none

Бренд: ADTRAN Страницы: 2

Бренд: CAME Страницы: 32

Бренд: Altimium Страницы: 12

Security Router X-PeditionTM

Бренд: Enterasys Страницы: 466

Бренд: Alcatel Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды