Avaya ERS 8600 series Скачать руководство пользователя

Страница: 402 / 420

Table 43: Command parameters

Parameter

Description

act-id

Specifies a unique identifier (in the range 1
through 4096) for this ACT entry.

If you provide no

<act-id>

, the command shows switch-wide ACT configuration data.

Important:

Any show command that displays information that cannot fit on one screen appears as two

tables: Part 1 and Part 2.

ACT pattern data

Use the

show filter act-pattern

command to display ACT pattern data. The syntax for

this command is as follows.

show filter act-pattern [

<act-id>

]

The following table explains parameters for this command.

Table 44: Command parameters

Parameter

Description

act-id

Specifies a unique identifier (in the range 1–
4096) for this ACT entry.

The following figure shows sample output for this command.

Figure 50: show filter act-pattern command output

ACLI show commands

402 Configuration — IPv6 Routing

November 2010

Содержание ERS 8600 series





































































































































































































































































































































































































































Результаты поиска

Содержание ERS 8600 series

Отзывы:

Похожие инструкции для ERS 8600 series

Бренды по названию

Популярные бренды

Avaya ERS 8600 series, Руководство по настройке

Результаты поиска

Содержание ERS 8600 series

Отзывы:

Похожие инструкции для ERS 8600 series

Бренды по названию

Популярные бренды