Avaya ERS 8600 series Скачать руководство пользователя

Страница: 330 / 420

Variable

Value

acl-id

Specifies an ACL ID in the range of 1–4096.

add

<vid>

[

<vid2-vid3>

]

Associates a VLAN or a VLAN list with a particular
ACL.

<vid>

is a list of VLANs separated by a comma

or a range of VLANs specified as low-high [vlan-id -
vlan-id].

info

Displays the ACL VLAN status.

remove

<vid>

[

<vid2-vid3>

]

Removes a VLAN or VLAN list from a particular ACL.

<vid>

is a list of VLANs separated by a comma or a

range of VLANs specified as low-high [vlan-id -vlan-
id].

Associating ports for an ACL

Associate or remove ports for a particular ACL.

Procedure steps

Associate or remove ports by using the following command:

config filter acl

<acl-id>

port

Variable definitions

Use the data in the following table to use the

config filter acl port

command.

Variable

Value

acl-id

Specifies an ACL ID in the range 1–4096.

add

<ports>

]

Associates a port or a port list with a particular ACL.

<ports>

is a list of ports separated by a comma or a

range of ports specified as low-high [slot/port-slot/
port].

info

Displays the ACL port status.

remove

<ports>

Removes a port or a port list from a particular ACL.

<ports>

is a list of ports separated by a comma or a

range of ports specified as low-high [slot/port-slot/
port].

IPv6 traffic filter configuration using the CLI

330 Configuration — IPv6 Routing

November 2010

Содержание ERS 8600 series





































































































































































































































































































































































































































Результаты поиска

Содержание ERS 8600 series

Отзывы:

Похожие инструкции для ERS 8600 series

Бренды по названию

Популярные бренды

Avaya ERS 8600 series, Руководство по настройке

Результаты поиска

Содержание ERS 8600 series

Отзывы:

Похожие инструкции для ERS 8600 series

Бренды по названию

Популярные бренды