Avaya ERS 8600 series Скачать руководство пользователя

Страница: 327 / 420

Variable

Value

name

<pattern-name>

Renames the pattern with a new name that you define. Each of
the three patterns must use a unique name.

pattername

Specifies a pattern name with a range 0–32 characters.

Applying the ACT

After you create and configure the ACT, apply it to implement the configuration.

Procedure steps

Apply the ACT by using the following command:

configure filter act

<act id>

apply

Configuring ACLs

Configure access control lists (ACL) to create lists of rules for the ACT.

Important:

If the ACT contains IPv6 attributes, you must configure an ACL of pktType IPv6. If the ACT

uses only Ethernet attributes, you can configure one ACL of pktType IPv4 and an ACL of

pktType IPv6.

Procedure steps

Configure an ACL by using the following command:

config filter acl

<acl-id>

Variable definitions

Use the data in the following table to use the

config filter acl

command.

Applying the ACT

Configuration — IPv6 Routing

November 2010 327

Содержание ERS 8600 series





































































































































































































































































































































































































































Результаты поиска

Содержание ERS 8600 series

Отзывы:

Похожие инструкции для ERS 8600 series

Бренды по названию

Популярные бренды

Avaya ERS 8600 series, Руководство по настройке

Результаты поиска

Содержание ERS 8600 series

Отзывы:

Похожие инструкции для ERS 8600 series

Бренды по названию

Популярные бренды