Avaya ERS 8600 series Скачать руководство пользователя

Страница: 323 / 420

Command

Parameter

config filter acl <acl-id> vlan

add <vid> [<vid2-vid3>]

remove <vid> [<vid2-vid3>]

info

config filter act <act-id>

create [name <value>]

delete

apply

name <value>

info

arp <arp-attributes>

ip <ip-attributes>

ipv6 <ipv6-attributes>

ethernet <ethernet-attributes>

protocol <protocol-attributes>

config filter act <act-id> pattern <pattern-
name>

add <base> <offset> <length>

name <pattern-name>

info

Configuring ACTs

Configure an access control template (ACT) to create, delete, apply, and specify attributes.

After you apply the ACT you cannot change the attributes. ACT IDs 4001 to 4096 are reserved

for system-defined ACTs.

System-defined ACTs are available for filters as required.

Important:

An ACT can use IPv4 or IPv6 attributes, but not both. You cannot combine IPv4 and IPv6

attributes in the same ACL.

Procedure steps

Configure an ACT by using the following command:

Configuring ACTs

Configuration — IPv6 Routing

November 2010 323

Содержание ERS 8600 series





































































































































































































































































































































































































































Результаты поиска

Содержание ERS 8600 series

Отзывы:

Похожие инструкции для ERS 8600 series

Бренды по названию

Популярные бренды

Avaya ERS 8600 series, Руководство по настройке

Результаты поиска

Содержание ERS 8600 series

Отзывы:

Похожие инструкции для ERS 8600 series

Бренды по названию

Популярные бренды