Avaya ERS 8600 series Скачать руководство пользователя | Manualshive

Страница: 314 / 420

background image

Inserting ACE common entries

Insert access control entries (ACE) to add an ACE to an ACL.

Procedure steps

1. In the navigation tree, open the following folders:

Configuration, Security, Data

Path

.

2. Double-click

Advanced Filters (ACE/ACLs)

.

3. Click the

ACL

tab.

4. Select the ACL to which to add an ACE.
5. Click the

ACE

button.

6. Click

Insert

.

7. Type data in the required fields.
8. Click

Insert

.

Variable definitions

Use the data in the following table to configure the ACE.

Variable

Value

AceId

Specifies a unique identifier and priority for the ACE.

Name

Specifies a descriptive, user-defined name for the
ACE entry. The system automatically assigns a name
if you do not choose one.

Mode

Indicates the operating mode associated with the
ACE. Valid options are deny and permit, with none as
the default.

MltIndex

Specifies whether to override the MLT index picked by
the MLT algorithm when a packet is sent on MLT ports.
Valid values range 0–8, with 0 as the default.

RemarkDscp

Specifies whether the Differentiated Services Code
Point (DSCP) field value marks non standard traffic
classes and local use Per Hop Behavior (PHB). The
default is disable.

RemarkDot1Priority

Specifies whether Dot1 Priority as described by Layer
2 standards, 802.1Q, and 802.1P is enabled. The
default is disable.

IPv6 traffic filter configuration using Enterprise Device Manager

314 Configuration — IPv6 Routing

November 2010

«
...
312
313
314
315
316
...
»

Содержание ERS 8600 series





































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ERS 8600 series

Бренд: SAF Страницы: 30

Бренд: peplink Страницы: 2

Бренд: Gbord Страницы: 8

Hotwire ATM Line Cards 8335

Бренд: Paradyne Страницы: 132

Бренд: Grundig Страницы: 24

Ethernet MCA 10/100 Adapter

Бренд: Olicom Страницы: 88

Бренд: Chase Research Страницы: 114

Бренд: ADDON Страницы: 4

Бренд: Ryobi Страницы: 44

Бренд: Netopia Страницы: 138

Бренд: TRENDnet Страницы: 2

Бренд: CalAmp Страницы: 52

Linktropy MINI-G

Бренд: Apposite Technologies Страницы: 57

Бренд: National Instruments Страницы: 36

Бренд: Divio Страницы: 78

BNI EIP-508 05-Z015 Series

Бренд: Balluff Страницы: 74

The DSX Value Solution (Japanese) LDX154

Бренд: ADC Страницы: 4

Бренд: KTI Networks Страницы: 147

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды