Avaya ERS 8600 series Скачать руководство пользователя

Страница: 297 / 420

config vlan

<vid>

ipv6 mld

Variable definitions

Use the data in the following table to use the

config vlan ipv6 mld

command.

Variable

Value

info

Displays the current VLAN MLD configuration setting.

last-memb-query-int

<seconds>

Configures the query interval time in 1/10 of a second
for the last member.

seconds

is in the range 0–65535.

query-interval

<seconds>

Configures the query interval time in 1/10 of a second.

seconds

is in the range 0–65535.

query-maxresp

<1seconds>

The maximum query response time advertised in MLD
queries on this interface.

seconds

is in the range 0–65535.

robustval

<integer>

Configures the robustness value.

integer

is in the range 0–65535.

version <1|2>

Configures the version of MLD to version 1 or version
2.

<vid>

Specifies a VLAN ID in the range of 1–4094.

Enabling multicasting on a brouter port

Configure multicasting on a brouter port to enable MLD on the port.

Procedure steps

Enable multicasting by using the following command:

config ethernet <ports> ipv6 mcast <enable|disable>

Variable definitions

Use the data in the following table to use the

config ethernet ipv6 mcast

command.

Enabling multicasting on a brouter port

Configuration — IPv6 Routing

November 2010 297

Содержание ERS 8600 series





































































































































































































































































































































































































































Результаты поиска

Содержание ERS 8600 series

Отзывы:

Похожие инструкции для ERS 8600 series

Бренды по названию

Популярные бренды

Avaya ERS 8600 series, Руководство по настройке

Результаты поиска

Содержание ERS 8600 series

Отзывы:

Похожие инструкции для ERS 8600 series

Бренды по названию

Популярные бренды