Avaya ERS 8600 series Скачать руководство пользователя | Manualshive

Страница: 28 / 420

background image

Protocol defines a standard format primarily known as the IP header, required for successful
delivery of datagrams.

Transport and routing protocols are not physical media dependant. The next hop path
calculated by the routing protocol in path from the source to the destination can result in the
next hop being connected on an Ethernet interface. In this case, the next-hop router must
request a mapping of a next-hop IPv6 address to a 48-bit MAC address. The IPv6 Neighbor
Discovery Protocol, described in RFC2461, defines a mechanism to identify existing or
upcoming neighbors in the network. This mechanism combines the ARP, router discovery, and
redirect information. Due to this combination of features, the mechanism supports the
autoconfiguration of host entities.

IPv6 requires installed R or RS modules in the Avaya Ethernet Routing Switch 8800/8600
chassis. IPv6 also requires at least one 8692 SF/CPU Enterprise Enhanced SF/CPU with
SuperMezz or at least one 8895 SF/CPU (no SuperMezz is required on the 8895 SF/CPU).
IPv6 on the Avaya Ethernet Routing Switch 8800/8600 basic redistribution uses Open Shortest
Path First (OSPF) v3, local, and static routes. Nonlocal next-hop static routes are possible.

Management access

The Avaya Ethernet Routing Switch 8800/8600 contains an Ethernet port for both master and
standby SF/CPUs. You configure these Ethernet ports differently from the regular switch ports.
In IPv4, the protocol stack operating for these ports is different from the switch IP stack. The
IPv6 functionality for the SF/CPU Ethernet port is offered only when the switch operational
state is up, and is not offered from the boot monitor level.

The management port provides two functions:

• configuring IPv6 after the system boots up in the CLI and device management through

the configured IPv6 address

• configuring static routes reachable through the management route for connectivity

IPv6 supports multiple addresses on each interface and for multiple addresses to management
IP interface.

In addition to the management port, you can configure management routes to reach nonlocal
destinations.

The Avaya Ethernet Routing Switch 8800/8600 advertises the management port and the
management route to the regular routing domain (OSPFv3), but does not include the prefix for
the interface in the router advertisement.

IPv6 routing fundamentals

28 Configuration — IPv6 Routing

November 2010

«
...
26
27
28
29
30
...
»

Содержание ERS 8600 series





































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ERS 8600 series

Бренд: H3C Страницы: 22

Бренд: H3C Страницы: 3

DM/IP601-CPCI-100BT

Бренд: Dialogic Страницы: 2

EdgeLens INT10G8LR56

Бренд: Garland Страницы: 30

Бренд: Netis Страницы: 16

Бренд: H3C Страницы: 9

ADSL2+ Wireless MIMO Router

Бренд: Ace Страницы: 64

Бренд: Tripp Lite Страницы: 2

Бренд: ZyXEL Communications Страницы: 30

Бренд: Wave Wireless Networking Страницы: 167

Acme Packet 3900

Бренд: Oracle Страницы: 70

DiskStation Series

Бренд: Synology Страницы: 6

ibaBM-FOX-i-3o-D

Бренд: IBA Страницы: 13

32R1860 - Nortel Layer 2/3 Copper GbE Switch...

Бренд: IBM Страницы: 14

Бренд: I-Tech Страницы: 6

Бренд: IC Realtime Страницы: 8

Ethernet ISA Card

Бренд: Farallon Страницы: 20

Бренд: Magnescale Страницы: 73

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды