Avaya ERS 8600 series Скачать руководство пользователя | Manualshive

Страница: 190 / 420

background image

Important:

You must use an IPv6 link-local address as an NBMA neighbor.

Variable definitions

Use the data in the following table to use the

ipv6 ospf nbma-nbr

command.

Variable

Value

Ipv6address/prefix-len

Specifies the IPv6 address of the neighbor as a string
of 0–43 characters.

priority

<priority>

Configures the OSPF priority for the interface during
the election process for the designated router. The
interface with the highest priority number is the
designated router. The interface with the second-
highest priority becomes the backup designated
router. If the priority is 0, the interface cannot become
either the designated router or a backup. The priority
is used only during election of the designated router
and backup designated router. The range is 0 to 255.
The default is 1. To configure this option to the default
value, use the default operator with the command.

Configuring OSPF parameters for a VLAN

Configure OSPFv3 parameters for a specified VLAN to customize your OSPF IPv6

configuration.

Prerequisites

You must log on to the VLAN Interface Configuration mode in the ACLI.

Procedure steps

1. Associate the OSPF area with an interface by using the following command:

ipv6 ospf area <A.B.C.D>

2. Enable OSPF on the interface with the following command:

IPv6 routing configuration using the ACLI

190 Configuration — IPv6 Routing

November 2010

«
...
188
189
190
191
192
...
»

Содержание ERS 8600 series





































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ERS 8600 series

Бренд: D-Link Страницы: 12

Бренд: BandLuxe Страницы: 67

Бренд: Icidu Страницы: 10

Бренд: Paradyne Страницы: 2

Бренд: Paradyne Страницы: 20

Бренд: Paradyne Страницы: 2

Бренд: Zhone Страницы: 2

COMSPHERE 6800 Series

Бренд: Paradyne Страницы: 155

COMSPHERE 6800 Series

Бренд: Paradyne Страницы: 44

Бренд: T&D Страницы: 122

Бренд: Gigabyte Страницы: 18

Бренд: XtendLan Страницы: 21

Бренд: Ariesys Страницы: 10

Бренд: Lantronix Страницы: 75

Бренд: Linksys Страницы: 80

Бренд: Matrix Switch Corporation Страницы: 54

Бренд: WIN Enterprises Страницы: 25

Бренд: RouterBOARD Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды