Avaya ERS 8600 series Скачать руководство пользователя

Страница: 163 / 420

Configuring OSPF area ranges

Configure an area address range on the OSPF router to reduce the number of ABR

advertisements into other OSPF areas. An area address range is an implied contiguous range

of area network addresses for which the ABR advertises a single summary route.

You can use any value for the OSPF area name (for example, 1.1.1.1 or 200.200.200.200).

Procedure steps

Configure an OSPF area range by using the following command:

config ipv6 ospf area

<ipaddr>

range

<ipv6addr-prefix>

Variable definitions

Use the data in the following table to use the

config ipv6 ospf area range

command.

Variable

Value

advertise-metric

<cost>

lsa-type

<value>

Specifies the advertise metric value and LSA type.

•

cost

is the advertise metric vlaue in the range 0–

65535.

•

value

is the LSA type as either inter-area-prefix-

link or nssa-extlink.

advertise-mode <advertise|no-
advertise>

Specifies the area range advertise mode as advertise
or no-advertise.

delete lsa-type <value>

Deletes an LSA type.

value

is the LSA type as either inter-area-prefix-

link or nssa-link.

create advertise-mode

<value>

lsa-

type

<value>

[advertise-metric

<value>

]

Creates an advertise mode for a range of IPv6 area
addresses.

• create advertise-mode

<value>

is advertise or no-

advertise.

• lsa-type

<value> value

is the LSA type as either

inter-area-prefix-link or nssa-extlink.

• advertise-metric

<value>

is the advertise metric 0–

65535.

Configuring OSPF area ranges

Configuration — IPv6 Routing

November 2010 163

Содержание ERS 8600 series





































































































































































































































































































































































































































Результаты поиска

Содержание ERS 8600 series

Отзывы:

Похожие инструкции для ERS 8600 series

Бренды по названию

Популярные бренды

Avaya ERS 8600 series, Руководство по настройке

Результаты поиска

Содержание ERS 8600 series

Отзывы:

Похожие инструкции для ERS 8600 series

Бренды по названию

Популярные бренды