Avaya ERS 8600 series Скачать руководство пользователя

Страница: 161 / 420

Configuring OSPF global parameters

Configure Open Shortest Path First (OSPF) version 3 global parameters to affect OSPF routing

on the entire switch. Routers use the OSPFv3 protocol to exchange network topology

information, providing each router with a map of the network.

Procedure steps

Configure OSPFv3 by using the following command:

config ipv6 ospf

Variable definitions

Use the data in the following table to use the

config ipv6 ospf

command.

Variable

Value

as-boundary-router

<enable|

disable>

Enables or disables the OSPF Autonomous System
boundary router. The default is disable.

disable

Globally disables OSPF on the switch.

enable

Globally enables OSPF on the switch.

info

Displays the current OSPF configuration on the
switch.

router-id

<RTR_ADDR>

Configures the OSPF router ID IPv4 address.

<RTR_ADDR>

is the IPv4 address in dotted decimal

format {a.b.c.d}.

Configuring OSPF areas

OSPF supports hierarchical routing by dividing the Autonomous System into different areas.

When two or more areas exist, the backbone area (area 0.0.0.0) must always be present.

You can use any value for the OSPF area name (for example, 1.1.1.1 or 200.200.200.200).

Configuring OSPF global parameters

Configuration — IPv6 Routing

November 2010 161

Содержание ERS 8600 series





































































































































































































































































































































































































































Результаты поиска

Содержание ERS 8600 series

Отзывы:

Похожие инструкции для ERS 8600 series

Бренды по названию

Популярные бренды

Avaya ERS 8600 series, Руководство по настройке

Результаты поиска

Содержание ERS 8600 series

Отзывы:

Похожие инструкции для ERS 8600 series

Бренды по названию

Популярные бренды