Avaya ERS 8600 series Скачать руководство пользователя

Страница: 152 / 420

Inserting OSPF area aggregate ranges

Configure an area address range on the OSPF router to reduce the number of ABR

advertisements into other OSPF areas. An area address range is an implied contiguous range

of area network addresses for which the ABR advertises a single summary route.

You can use any value for the OSPF area name (for example, 1.1.1.1 or 200.200.200.200).

Procedure steps

1. In the navigation tree, open the following folders: Configuration, IPv6.
2. Double-click

OSPF

3. Click the

Area Aggregate

tab.

4. Click

Insert

5. In the

AreaId

box, click the ellipsis button (...) to select the required area ID of the

aggregate address.

6. In the

AreaLsdbType

box, select the required option:

• interAreaPrefixLsa: to generate an aggregated summary
• nssaExternalLink: to generate an NSSA link summary

7. In the

Prefix

box, type the prefix of the area IPv6 address.

8. In the

Prefix Length

box, type the number of bits you want to advertise from the

IPv6 address.

9. In the

Effect

box, select the required option:

• advertiseMatching: to advertise the aggregate summary LSA with the same

link-state ID

• doNotAdvertiseMatching: to suppress all networks that fall within the entire

range

10. In the

AdvertiseMetric

box, type a cost value (in the range 0 to 65535) to advertise

for the OSPF area range.

11. Click

Insert

Variable definitions

Use the data in the following table to configure the IPv6 OSPF area aggregate.

IPv6 routing configuration using Enterprise Device Manager

152 Configuration — IPv6 Routing

November 2010

Содержание ERS 8600 series





































































































































































































































































































































































































































Результаты поиска

Содержание ERS 8600 series

Отзывы:

Похожие инструкции для ERS 8600 series

Бренды по названию

Популярные бренды

Avaya ERS 8600 series, Руководство по настройке

Результаты поиска

Содержание ERS 8600 series

Отзывы:

Похожие инструкции для ERS 8600 series

Бренды по названию

Популярные бренды