Avaya ERS 8600 series Скачать руководство пользователя | Manualshive

Страница: 128 / 420

background image

Variable

Value

no-autoconfig <false|true>

If true, the prefix is used for autonomous
address configuration.
The default value is true.

eui <1-3>

(1) eui (extended unique identifier) not
used, (2) eui with U/L (Universal/Local bit)
complement enabled, (3) eui used without
u/l.
The default value is eui not used.

infinite

Configures the prefix as infinite.
The default value is disable.

no-advertise

Removes the prefix from the neighbor
advertisement. Use the no operator to
remove this option. Use the default
operator to configure this value to the
default setting.
The default value is disable.

no-onlink <false|true>

If true, onlink determination uses the prefix.
This value is placed in the L-bit field in the
prefix information option. It is a 1-bit flag.
The default value is true.

preferred-life <seconds>

Configures the preferred life, in seconds.
The valid range is 0–3600000. Use the
default operator to configure this value to
the default setting.
The default value is 604800.

prefix/prefix length

Specifies the IP address and prefix.

valid-life <seconds>

Configures the valid life, in seconds. The
valid range is 0–3600000. Use the default
operator to configure this value to the
default setting.
The default value is 2592000.

Configuring route advertisement

Use route advertisement to discover potential default routers in a network and to discover link

information.

Basic IPv6 configuration using the ACLI

128 Configuration — IPv6 Routing

November 2010

«
...
126
127
128
129
130
...
»

Содержание ERS 8600 series





































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ERS 8600 series

Бренд: D-Link Страницы: 13

Бренд: Parkside Страницы: 55

Бренд: Parkside Страницы: 34

RealPort Ethernet 10/100

Бренд: Xircom Страницы: 30

Бренд: Tektronix Страницы: 178

Бренд: Galaxy Страницы: 30

PowerBeam PBE-5AC-400-ISO

Бренд: Ubiquiti Страницы: 23

Бренд: Patton Страницы: 62

Бренд: Idis Страницы: 20

UniFi LED ULED-AT

Бренд: Ubiquiti Страницы: 16

Бренд: DPS Страницы: 57

IP Board IPT10000C

Бренд: Dialogic Страницы: 2

Бренд: ATTO Technology Страницы: 2

CyberPower RMCARD201

Бренд: CyberPower Страницы: 8

Бренд: Aerotech Страницы: 62

ACC-BKT-AX-BEAM

Бренд: Extreme Networks Страницы: 35

Бренд: LevelOne Страницы: 17

Бренд: H3C Страницы: 148

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды