Avaya ERS 8600 series Скачать руководство пользователя | Manualshive

Страница: 124 / 420

background image

ipv6 interface [address-type <1-2>] [mtu <bytes>] [muticast-

routing] [reachacble-time <ms>] [retransmit-time <ms>] [vlan

<vlan id>]

Variable definitions

Use the data in the following table to use the

ipv6 interface

and

ipv6 interface

address

commands.

Variable

Value

address <ipv6 address>

Configures the IPv6 address and prefix length in
the format address and prefix length.
The default value is none.

address-type <1-2>

1—unicast, 2—anycast.
The default value is 1—unicast.

mtu <bytes>

Configures the maximum transmission unit for the
interface.
The default value is 1500.

multicast-routing

Enables or disables MLD.
The default value is disable.

reachable-time <ms>

Configures the time, in milliseconds, that a
neighbor is considered reachable after receiving
a reachability confirmation.
The default value is 30000.

retransmit-time <ms>

Configures the time, in milliseconds, between
retransmissions of Neighbor Solicitation
messages to a neighbor when resolving the
address or when probing the reachability of a
neighbor.
The default value is 1000.

vlan <vlan id>

Specifies the VLAN ID.

Configuring the VLAN as an IPv6 VLAN

Configure a VLAN as an IPv6 VLAN to use IPv6 routing on the VLAN.

Basic IPv6 configuration using the ACLI

124 Configuration — IPv6 Routing

November 2010

«
...
122
123
124
125
126
...
»

Содержание ERS 8600 series





































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ERS 8600 series

Бренд: N-Tron Страницы: 101

Бренд: D-Link Страницы: 10

Бренд: C&H Technologies Страницы: 46

Бренд: Campbell Страницы: 42

Бренд: IBM Страницы: 104

System Storage TS3100

Бренд: IBM Страницы: 375

Бренд: TP-Link Страницы: 73

Бренд: FOR-A Страницы: 2

PG-FLEX RT FRL-752

Бренд: PairGain Страницы: 6

Бренд: Genie Страницы: 15

Бренд: Uniflair Страницы: 24

Бренд: National Instruments Страницы: 56

Бренд: Maipu Страницы: 26

FrameSaver DSL 9788 Router

Бренд: Paradyne Страницы: 28

OmniTik UPA-5HnD

Бренд: RouterBOARD Страницы: 4

Бренд: Rajant Страницы: 93

Redbooks Emulex VFA5

Бренд: IBM Страницы: 15

Бренд: Proxim Страницы: 65

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды