Avaya ERS 8600 series Скачать руководство пользователя

Страница: 111 / 420

config vlan <vlan id> ipv6 delete addr

<Ipv6 address>

2. Delete the IPv6 address on a brouter port by using the following command:

config ethernet <slot/port> ipv6 delete addr

<IPv6 address>

Variable definitions

Use the data in the following table to use the

config vlan ipv6 delete addr

and

config ethernet ipv6 delete addr

commands.

Variable

Value

IPv6 address

Specifies the IPv6 address to delete.

slot/port

Specifies the slot and port location of the
brouter port from which to delete the IPv6
address.

vlan id

Specifies the ID of the VLAN from which to
delete the IPv6 address.

Example of deleting an IPv6 address

Procedure steps

1. Delete the IPv6 address on a VLAN:

ERS-8610:5#

config vlan 13 ipv6 delete addr 9898::1

2. Delete the IPv6 address on a brouter port:

ERS-8610:5#

config ethernet 1/18 ipv6 delete addr 4040::1

Deleting an IPv6 interface

Delete an IPv6 interface to remove it from the configuration.

Procedure steps

1. Delete an IPv6 interface from a VLAN by using the following command:

Deleting an IPv6 interface

Configuration — IPv6 Routing

November 2010 111

Содержание ERS 8600 series





































































































































































































































































































































































































































Результаты поиска

Содержание ERS 8600 series

Отзывы:

Похожие инструкции для ERS 8600 series

Бренды по названию

Популярные бренды

Avaya ERS 8600 series, Руководство по настройке

Результаты поиска

Содержание ERS 8600 series

Отзывы:

Похожие инструкции для ERS 8600 series

Бренды по названию

Популярные бренды