Avaya ERS 8600 series Скачать руководство пользователя

Страница: 101 / 420

Variable

Value

<vid>

Specifies the VLAN ID (from 1-4094).

Configuring the VLAN as an IPv6 VLAN

Configure a VLAN as an IPv6 VLAN to use IPv6 routing on the VLAN.

Prerequisites

You must create the VLAN before you configure it as an IPv6 VLAN.

Procedure steps

Configure the VLAN by using the following command:

config vlan

<vlan ID>

ipv6 create

Variable definitions

Use the data in the following table to use the

config vlan ipv6 create

command.

Variable

Value

addr

Specifies the IPv6 address and prefix length in
the format address and prefix length.

addr-type

1—unicast, 2—anycast.
The default values is 1—unicast.

admin

Enables or disables the administrative state of the
interface.

delete

Deletes one of the following:

• addr <value>

• all

• interface

descr

Views or updates the description for the interface.

info

Displays information about the configuration.

Configuring the VLAN as an IPv6 VLAN

Configuration — IPv6 Routing

November 2010 101

Содержание ERS 8600 series





































































































































































































































































































































































































































Результаты поиска

Содержание ERS 8600 series

Отзывы:

Похожие инструкции для ERS 8600 series

Бренды по названию

Популярные бренды

Avaya ERS 8600 series, Руководство по настройке

Результаты поиска

Содержание ERS 8600 series

Отзывы:

Похожие инструкции для ERS 8600 series

Бренды по названию

Популярные бренды