Avaya DEFINITY Server R Скачать руководство пользователя страница 514 | Manualshive

Страница: 514 / 550

background image

Fiber Link Administration

555-233-115

A-4

Issue 7 November 2003

All Installations

1. When the system reset is finished, type status port-network 2 and press

Enter

. The Port Network Status screen appears. Verify that PNC Active is

“up” and that the Service State is “in.”

2. A Span LED, on the front of the DS1 Converter circuit pack, must be on for

each active facility administered. For example, if Facility A and Facility B
are administered, then the top 2 Span LEDs on the circuit pack must be on
(yellow). The yellow LEDs are on only if no problems were encountered
during the administration of hardware. Span LEDs associated with
non-administered facilities (C and D, in this example) should be off.

3. Perform a test call, if desired.

Administer Fiber Links on Duplex Systems

All non-duplicated Switch Node Interfaces to Switch Node Interface fiber links are
automatically duplicated. When PNC Duplication is enabled on the
System-Parameters Customer-Options form, the following administration forms
change:

■

Cabinet Form

—

Additional fields appear to allow administration of switch

nodes to A-PNC and B-PNC sides of the CSS. The B-PNC is the
duplicated hardware for the A-PNC. Either the A-PNC or the B-PNC can
provide full customized service. B-PNC cannot be used in a simplex PNC
configuration. Pairing of switch nodes is also defined here.

■

Fiber Link Administration Form

—

Additional fields appear to allow

administration of fiber links on the B-PNC side of the CSS. If an endpoint
on the A-PNC side is administered as an SNI, its corresponding endpoint
on the B-PNC side is determined (if switch nodes are paired in the cabinet
form prior to this administration) and displayed. However, administration of
the duplicate B-PNC link is not enforced until duplication is in full operation.

■

Duplication-Related System-Parameters Form

—

An additional field

appears to enable operation of PNC duplication.

1. Type change system-parameters customer-options and press

Enter

. On

Page 2 of the form, set the

PNC Duplication?

field to y. Press

Enter

.

2. Type change system-parameters duplication and press

Enter

. Change

the

Enable operation of PNC duplication?

field to y. Press

Enter

.

3. Type status pnc and press

Enter

. Verify the

Duplicated?

field is yes.

4. Type list fiber and press

Enter

. All administered fiber connections display.

5. If a previously used fiber link is to be reused, type add fiber <number>

and press

Enter

. If this is a new fiber link, type add fiber next and press

Enter

.

«
...
512
513
514
515
516
...
»

Содержание DEFINITY Server R







































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для DEFINITY Server R

Venus VNS563-4GD

Бренд: Diamond Systems Страницы: 43

Бренд: MSI Страницы: 22

Бренд: Biostar Страницы: 31

Бренд: Aaeon Страницы: 119

Бренд: ASROCK Страницы: 212

Бренд: Aaeon Страницы: 113

CS631-C246/Q370

Бренд: DFI Страницы: 79

Бренд: Intel Страницы: 73

Бренд: Advantech Страницы: 98

Бренд: JETWAY Страницы: 48

Бренд: Gigabyte Страницы: 96

Бренд: Ebyte Страницы: 9

Бренд: e2v Страницы: 39

Бренд: DFI Страницы: 80

Бренд: ASROCK Страницы: 139

Бренд: ASROCK Страницы: 163

Бренд: DFI-ITOX Страницы: 127

Бренд: Terra Страницы: 6

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды