manualshive.com logo in svg

Avaya DEFINITY SERIES, Руководство по установке и обслуживанию, Страница: 91 / 101

Поделиться
Скачать
Avaya DEFINITY SERIES Скачать руководство пользователя страница 91

DEFINITY Enterprise Communication Server Release 9
Installation and Maintenance for Survivable Remote EPN  

555-233-121  

Issue 2

November 2000

SREPN Maintenance 

2-37

110 block cross-connect pins 

2

110 block cross-connect pins

Table 2-12.

110 block cross-connect pins

SRP Aux

EPN Aux

Amphenol
Pin 
Number

Color

Cross-
Connect 
Pin 
Number

Lead 
Designation

a

a.

When the loop between Cust A (alarm) and Cust Rtn (return) closes, the SRSwitch configures the SRP into 
Restore mode, overriding the faceplate switch setting. Closure of the customer alarm relay is controlled by 
an SRP SAT command which closes the customer alarm relay on the SRP processor.

Pwr Fail (-48V) is grounded when the TN2301 detects that its -48V redundant power is bad.

Cust A (alarm) - see above.

SRPresent is always grounded, indicating to the TN775C (Maint.) that it is connected in a SREPN.

SRActive is generated by TN775C (Maint.) to disconnect links from Release 9r to SRP in Survive mode.

-48V In/Rtn is input and return used by DC/DC converter for supplying redundant power to the optical 
transceivers.

SR Cntrl/Rtn, when active, connects to the SR Cntrl Rtn signal on the TN775C (Maint.). Loop closed - 
TN2301 goes into Survive mode; loop open - TN2301 cannot come out of Survive mode without manual or 
remote reset.

Cross-
Connect 
Pin 
Number

Color

Amphenol
Pin 
Number

23

G-V

46

Cust Rtn

3

W-O

27

SRP Aux

SRP Switch

Amphenol
Pin 
Number

Color

Cross-
Connect 
Pin 
Number

Lead 
Designation

Cross-
Connect 
Pin 
Number

Color

Amphenol
Pin 
Number

27

W-O

3

Pwr Fail (-48V)

46

G-V

23

48

V-G

45

Cust A

23

BK-O

37

EPN Aux

SRP Switch

Amphenol
Pin 
Number

Color

Cross-
Connect 
Pin 
Number

Lead 
Designation

Cross-
Connect 
Pin 
Number

Color

Amphenol
Pin 
Number

02

O-W

4

Cust Rtn

24

O-BK

12

28

W-G

5

SRPresent

47

V-BR

49

29

W-BR

7

SRActive

48

BR-V

24

46

V-BL

41

-48V Rtn

41

V-BL

46

21

BL-V

42

-48V In

42

BL-V

21

48

V-G

45

b

b.

Momentarily short these two leads on the EPN Aux to verify the detection circuit on the TN2301 and the 
Maintenance (TN775C) circuit pack wiring.

SR Cntrl

43

V-O

47

23

G-V

46

b

SR Cntrl Rtn

44

O-V

22

Содержание DEFINITY SERIES






































































































Отзывы:

Нет отзывов