Avaya DEFINITY SERIES Скачать руководство пользователя страница 55

Страница: 55 / 101

SREPN Maintenance

2-1

Before starting to troubleshoot

DEFINITY Enterprise Communication Server Release 9
Installation and Maintenance for Survivable Remote EPN

555-233-121

Issue 2

November 2000

SREPN Maintenance

Before starting to troubleshoot

NOTE:

When the SRP is in Normal mode, the Expansion Interface circuit pack’s
yellow LED flashes (see

Table 2-6 on page 2-14

This is normal

. The links

to its counterpart in the R9r

are

down and are not re-established until the

SRP goes into Survive mode.

Similarly, after normal service is returned to the SREPN, the SRP is in an

alarmed state

This is normal for the SRP

and indicates that the TN2301 has

disconnected from the SREPN, and the SRP is no longer in control. EXP-
INTF errors and alarms and failures of Tests #237 and #238 are also
normal.

For more information about these conditions see

‘‘Post-reset check’’

Servicing the Survivable Remote EPN (SREPN) equipment involves both the
Release 9r and the R9si processors. Therefore, you may need to to refer to these
maintenance manuals:

■

DEFINITY ECS Release 9 — Maintenance for R9r

■

DEFINITY ECS Release 9 — Maintenance for R9si

Содержание DEFINITY SERIES






































































































Результаты поиска

Содержание DEFINITY SERIES

Отзывы:

Avaya DEFINITY SERIES, Руководство по установке и обслуживанию, Страница: 55 / 101

Результаты поиска

Содержание DEFINITY SERIES

Отзывы: