Avaya DEFINITY SERIES Скачать руководство пользователя страница 17

Страница: 17 / 101

DEFINITY Enterprise Communication Server Release 9
Installation and Maintenance for Survivable Remote EPN

555-233-121

Issue 2

November 2000

About This Document

xvii

Standards compliance

Standards compliance

The equipment presented in this document complies with the following (as
appropriate):

LASER Product

The DEFINITY ECS may contain a Class 1 LASER device if single-mode fiber
optic cable is connected to a remote expansion port network (EPN). The laser
device operates within the following parameters:

Maximum Power Output: -5 dBm
Wavelength: 1310 nm
Mode Field Diameter: 8.8 µm
CLASS 1 LASER PRODUCT
IEC 825 1993

DANGER:

Use of controls or adjustments or performance of procedures other than
those specified herein may result in hazardous radiation exposure.

Contact your Lucent Technologies representative for more information.

ITU-T (Formerly CCITT)

ANSI

Australia AS3260

ECMA

FCC Part 15 and Part 68

IEC 825

ETSI

EN55022

IEC950

IPNS

EN50081

UL 1459

DPNSS

EN50082

UL1950

National ISDN-1

UNI 3.1

CSA C222 Number 225

National ISDN-2

CISPR22

TS001

ISO-9000

Australia AS3548 (AS/NZ3548)

ILMI 3.1

Содержание DEFINITY SERIES






































































































Результаты поиска

Содержание DEFINITY SERIES

Отзывы:

Avaya DEFINITY SERIES, Руководство по установке и обслуживанию, Страница: 17 / 101

Результаты поиска

Содержание DEFINITY SERIES

Отзывы: