Avaya CallPilot 600r Скачать руководство пользователя страница 98

Страница: 98 / 106

600r server display non-default CMOS settings

This section describes the changes you must make to your non-default CMOS settings after
a successful BIOS upgrade. These changes are important to the operation of your server.

Note:

These settings are already enabled from the factory. You only need to change your non-

default CMOS settings if you upgrade your BIOS.

To view your non-default CMOS settings, perform the following steps:

1. Insert the CallPilot 600r DVD and select 3 from the Startup menu: Utilities (BIOS,

Firmware, etc...)

Result: The Avaya CallPilot Image Menu appears.

2. Select 3. 600r server Display Non-Default CMOS Settings.

Result: The following message appears: Enter Y to display a text file of the CMOS
settings. [Y,N]

3. Enter Y to display the text file.

Result: The following text file appears:

Note:

The text file that appears includes instructions to view and make changes to your

non-default CMOS settings.

******* BEGINNING OF TEXT DISPLAY*******

**************************************

*** Intel Chessne 1U BIOS Settings ***

*** Release 1 (January 26, 2006) ***

**************************************

a. During bootup press "F2" to edit the BIOS settings.

b. Under "Exit" load "Load Optimal Defaults."

c. Thereafter make the following changes:

a) BOOT->BOOT SETTINGS CONFIGURATION

QUIET BOOT

[DISABLED]

Maintaining the BIOS and system board firmware

98 Avaya CallPilot® 600r Server Maintenance and Diagnostics

December 2010

Содержание CallPilot 600r











































































































Результаты поиска

Содержание CallPilot 600r

Отзывы:

Avaya CallPilot 600r, Техническое обслуживание и диагностика, Страница: 98 / 106

Результаты поиска

Содержание CallPilot 600r

Отзывы: