Avaya CallPilot 600r Скачать руководство пользователя страница 24 | Manualshive

Страница: 24 / 106

Avaya CallPilot 600r Скачать руководство пользователя страница 24

Important:

If your system emits POST beep codes, record the beep code sequence and then call Avaya

technical support before attempting to correct the problem. Some POST beep codes are

fatal and can require that you replace the server.

The following table lists the POST error beep codes. The beep code occurs only after a critical
error occurs or after the BIOS fails to boot to the operating system. Note that not all error
conditions are supported by BIOS beep codes.

Table 6: POST beep codes

Beep count

Description

1, 2, or 3

Memory error. Reseat the memory or replace the Dual Inline Memory
Modules (DIMMs) with known good modules.

4 – 7 or 9 – 11

A fatal error indicates a possible serious system problem occurred.
Remove all the add-in cards and re-start the system. If the error still
occurs, contact Avaya support. If the beep codes are not generated after
the add-in cards are removed, insert the cards one at a time, booting the
system between each card addition, until the beeps occur again to reveal
the malfunctioning card.

8

A problem with the on-board video card occurred, indicating a fault on
the server board.

Interpreting BIOS error messages

After a recoverable error occurs during the POST, the BIOS displays an error message
describing the problem.

Important:

If your system displays BIOS error messages, record the error messages and then call

Avaya technical support before attempting to correct the problem.

BIOS error messages

BIOS error messages appear on the video monitor. Refer to the following table for a description
of the messages.

Troubleshooting your Avaya CallPilot® system

24 Avaya CallPilot® 600r Server Maintenance and Diagnostics

December 2010

«
...
22
23
24
25
26
...
»

Содержание CallPilot 600r











































































































Отзывы:

Нет отзывов