Avaya CallPilot 600r Скачать руководство пользователя страница 12 | Manualshive

Страница: 12 / 106

Avaya CallPilot 600r Скачать руководство пользователя страница 12

Figure 2: Front panel controls and LEDs

Note:

The faults described in the following table are hardware faults and are independent of Avaya

CallPilot® application faults.

Table 1: 600r Hardware Faults

Label

Control or feature

Label

Control or feature

A

Power button

M

NMI button (not used)

B

Reset button

L

ID button

C

Critical alarm LED

K

System ID LED (white)

D

Major fault LED

J

Network Interface Card (NIC)
activity LED (green)

E

Minor fault LED

I

Main power LED (green)

F

Power LED

H

not used

G

Disk 0 - activity (green) fault
(amber)

Rear panel controls and features

The following diagram shows the back panel controls and features of the 600r. The AC power
supply bank is on the right (E). The Peripheral Component Interconnect (PCI) card bracket
is in the middle of the back panel while the connectors and ports are along the bottom and left
side.

Outlining maintenance and diagnostics activities

12 Avaya CallPilot® 600r Server Maintenance and Diagnostics

December 2010

«
...
10
11
12
13
14
...
»

Содержание CallPilot 600r











































































































Отзывы:

Нет отзывов