Autonics PMC-1HS Series Скачать руководство пользователя страница 70

Страница: 70 / 82

9. Serial Communication Commands

© Copyright Reserved Autonics Co., Ltd.

9. Serial Communication Commands

9.1

Communication condition

Communication conditions

Descriptions

Communication speed

9600 to 115200bps

Data bit

8 bit

Stop bit

1 bit

Flow control

None

Parity bit

None

Control character

0-9, A-Z,

(Space), [CR] (Carriage return)

9.2

Command Cycle

(1)

means a space�

(2) [CR] means 0x0d carriage return.
(3) [LF] means 0x0a line feed.

9.3 Command

PRG

It executes a program in the PMC-1HS/PMC-2HS from an assigned address.

Format
Command

[Axis specification] [REG number specification] [CR]

PRG

[CR]

Y REG number (decimal)

Put the axis specification "X" in PMC-1HS.
[Example] To operate X/Y-axis from REG00

PRG

XY00 [CR]

Response: No-response

JOG

Start the continuous drive on the specified axis.

Format
Command

[Axis specification] [REG number specification] [CR]

JOG

+ X [CR]

- Y

Put the axis specification "X" in case of PMC-1HS.
[Example] To drive X-axis and Y-axis in the + and - directions respectively.

JOG

－

Y [CR]

The + direction can be omitted in the axis specification.

Response: No-response

Содержание PMC-1HS Series



















































































Результаты поиска

Содержание PMC-1HS Series

Отзывы:

Autonics PMC-1HS Series, Инструкция по эксплуатации, Страница: 70 / 82

Результаты поиска

Содержание PMC-1HS Series

Отзывы: