background image

GDO-8 Instruction Manual

22

26. Warranty

Product:  GDO-8 ShedMaster

®

 

Purchased from:______________________________Purchaser:___________________________________

 

 

                                                                     (described as “you” below)

Address:_____________________________________Installed by:__________________________________

Installed on (date):____________________________Invoice No:__________________________________

This Warranty is given by Automatic Technology (Australia) Pty Ltd (ABN 11 007 125 

368) (ATA), 6-8 Fiveways Boulevard, Keysborough 3173, 1300 133 944, sales@

automatictechnology.com.au

2.  The Competition and Consumer Act 2010 (including the Australian Consumer 

Law) and other relevant statutes provide a set of statutory consumer guarantees 

and other legal rights that cannot be excluded, restricted or modified by contract.  

This Warranty is in addition to and does not affect any of your rights under the 

Australian Consumer Law and other relevant statutes.

3.  Our goods come with guarantees that cannot be excluded under the Australian 

Consumer Law.  You are entitled to a replacement or refund for a major failure 

and for compensation of any other reasonably foreseeable loss or damage.  You 

are also entitled to have the goods repaired or replaced if the goods fail to be of 

acceptable quality and the failure does not amount to a major failure.

4.  Subject to your non-excludable rights under the Australian Consumer Law, 

ATA expressly excludes any liability for consequential loss, incidental or indirect 

damages (including but not limited to damages for loss of business profits, 

business interruption and loss of business information) due to a defect of the 

GDO-8 ShedMaster

®

 

(Product).  In particular any loss or damage caused to 

other equipment or accessories used with the product or any loss resulting from a 

delay in repair is excluded to extent permitted by law.  

5.  Subject to all of the matters set out below, ATA warrants in relation to the Product 

that:

(a) the Product’s drive units will be free of any defects in material and workmanship 

for 

at least 2 years after the date of purchase (as evidenced by the sales 

docket receipt), or 5000 cycles, which ever occurs first; and

(b) the Product’s other components and accessories will be free of any defects in 

material and workmanship for at least 12 months after the date of purchase (as 

evidenced by the sales docket receipt).

6.  No additional warranty will apply for Products repaired during the relevant 

warranty period.

7.  For all Products repaired outside the warranty period, a six (6) month warranty that 

the Product will be free of any defects in material and workmanship will apply from 

the date of dispatch of the Product to you.  ATA may charge you for any repairs 

undertaken outside the warranty period, and will provide you with a quotation in 

relation to any such costs for your approval before proceeding with any repairs.

8.  This Warranty applies only where you:

(a) immediately notify ATA at the contact details provided in paragraph 1 above 

or notify the or the retailer that you purchased the Product from of the alleged 

defect;

(b) return the product to the retailer that you purchased the Product from; and 

(c)  present the relevant sales docket and this Warranty document to the retailer to 

confirm the date of purchase.

9.  Except for this Warranty, ATA gives no warranties of any kind whatsoever (whether 

express or implied), in relation to the product, and, subject to paragraph 1 above, 

all warranties of whatsoever kind relating to the product are hereby excluded.

10. This Warranty excludes damage resulting from:

(a) normal wear and tear;

(b) accidental damage;

(c)  incorrect installation of the Product;

(d) blown fuses, electrical surges, power surges or power spikes;

(e) theft, fire, flood, rain, water, lightning, storms or any other acts of God;

(f)  any installation, configuration or use of the Product contrary to the instructions 

supplied with the Product;

(g) maximum continuous operating time exceeding 1 minute in 10;

(h) the operating force exceeding 15kg* (150 Newton) when moving the door 

manually to the open or closed position;

(i)  the door surface area exceeding 16.5m

2

 for 

GDO-8 ShedMaster

®

;

(j)  the door used with the Product not being in safe working order and condition;

(k)  repairs which are not authorised by ATA;

(l)  any failure to install or maintain the Product in accordance with the instructions 

supplied with the Product;

(m) any use which is not in accordance with the instructions provided with the Product;

(n) deliberate or negligent damage to the Product;

(o) any unauthorised modification to the Product;

(p) faulty or unsuitable wiring in the building in which the Product is installed;

(q) damage caused by insects;

(r)  any cost or expense relating to the recall of the Product;

(s)  installation of a residential garage door opener in a commercial or industrial premises 

or in a dwelling other than a single-family dwelling;

(t)  radio or electrical interference; or

(u) acts or omissions of any person (including service providers approved by ATA) other 

than ATA.

11. ATA’s liability under this Warranty is limited, at ATA’s absolute option, to replacing or 

repairing the product which ATA, in its unfettered opinion, considers to be defective 

either in material and/or workmanship or to credit the dealer with the price at which 

the product was purchased by the dealer.

12. This Warranty does not extend to cover labour for installation of the Product following 

repairs, the cost of which must be borne by you.

13. This Warranty is limited to Return-to-Base (RTB) repair and does not cover labour for 

on-site attendance, the cost of which must be borne by you.

14. Except as specified in this Warranty, ATA will not charge you for any repairs or 

replacements conducted under the Warranty.  However, ATA will charge you for any 

repairs which are not within the scope of this Warranty (or which are not required to 

be undertaken free of charge pursuant to the Australian Consumer Law).

15. This Warranty is void if the Product is not returned to the manufacturer in original or 

suitably secure packaging.

16. This Warranty is only applicable for repairs to the product carried out within Australia. 

17. This Warranty does not cover consumable items including, without limitation, globes, 

batteries and fuses. 

18. This Warranty is not transferable. 

19. Where the Product is retailed by any person other than ATA, except for the warranty 

set out above, such person has no authority from ATA to give any warranty or 

guarantee on ATA’s behalf in addition to the warranty set out above.

20. Any provision of this Warranty that is prohibited or unenforceable in any jurisdiction 

is ineffective as to that jurisdiction to the extent of the prohibition or unenforceability.  

That does not invalidate the remaining provisions of this Warranty nor affect the 

validity or enforceability of that provision in any other jurisdiction.

21. Products presented for repair may be replaced by refurbished goods of the same 

type rather than being repaired.  Refurbished parts may be used to repair the 

Product.

NOTES:

1.  One (1) cycle = one (1) open and one (1) close action of the door.

2.  This Warranty is to be read in conjunction with the owner’s copy of the installation 

instruction manual.

3.  * The door that the Product is used with should be balanced in such a way that the 

user is able to open or close the door manually using a force not greater than 150 

Newton (15 kg), other than to initially cause the door to start moving, which may 

require force in excess of that specified in this paragraph.

Содержание GDO-8 ShedMaster

























Отзывы: