Automated Logic UNI/59 Скачать руководство пользователя страница 10 | Manualshive

Страница: 10 / 10

Automated Logic UNI/59 Скачать руководство пользователя страница 10

Revised 1/3/01 • UNI/59

10

© 2001 Automated Logic Corporation

Protection

The UNI/59 module is protected by internal
solid state Polyswitches on the incoming
power and CMnet. These Polyswitches are
not replaceable and will reset themselves if
the condition that caused the fault returns to
normal.

Production Date

To determine when a module was
manufactured, check the module status
report for the module in SuperVision. Refer to
the

SuperVision User’s Guide

for more

information about the module status report.

A sticker on the back of the module also
shows the date the module was
manufactured. The first three characters on
the sticker indicate the type of module. The
next two characters show the year and month
of manufacture. (The month digit is in
hexadecimal.)

2 flashes
per second

On

Exec halted after frequent
system errors or GFBs
halted

5 flashes
per second

On

Exec start-up aborted, Boot
is running

5 flashes
per second

Off

Firmware transfer in
progress, Boot is running

7 flashes
per second

7 flashes per
second,
alternating
with Run LED

Ten second recovery period
after brownout

14 flashes
per second

14 flashes per
second,
alternating
with Run LED

Brownout

Table 2. LED Signals (Continued)

Run LED

Error LED

Condition

«
...
8
9
10

Содержание UNI/59











Отзывы:

Нет отзывов