AutoCrib RoboCrib 2000 E Скачать руководство пользователя страница 8 | Manualshive

Страница: 8 / 53

background image

Installation

8 |

P a g e

Cautions

The following cautionary information should be reviewed before the machine is installed. Following these requirements
and warnings are required.

CAUTION

: This machine is designed for indoor usage only. Any other usage will void

the Manufacturer’s Warranty.

Voltage and Polarity Check

It is important that this machine be hooked up to the proper voltage and polarity for
your country. Use a voltmeter to verify voltage and polarity before connecting the
machine to a wall outlet. For machines located in North America, use the diagram
below to verify correct voltages.

CAUTION:

Any procedure marked with the symbol at left requires that the Machine

have the power applied and a shock hazard exists.

CAUTION:

It is important that this machine be hooked up to the proper voltage and

polarity for your country. Use a Voltmeter to verify voltage and polarity. Should the
reading be any different from a normal reading or if you are unsure of what the
reading should be contact an electrician.

CAUTION:

Different countries may have unique plug arrangements. Ensure that the

machine is properly grounded before operating.

CAUTION:

The machine is a heavy item. Ensure that sufficient personnel are

available for lifting and transporting the machine. Use proper lifting procedures and
equipment.

CAUTION:

The system components in this machine utilize static sensitive

components. Precautions for handling sensitive devices should be observed when
handling these items.

Voltage and Polarity Check

(for Machines located in North America Only)

It is important that this machine is hooked up to proper voltage and polarity. Using a voltmeter, perform the following
checks from the illustration below.

«
...
6
7
8
9
10
...
»

Содержание RoboCrib 2000 E






















































Отзывы:

Нет отзывов

Похожие инструкции для RoboCrib 2000 E

Бренд: Jack Страницы: 66

Бренд: Jack Страницы: 132

Бренд: Janome Страницы: 43

Бренд: Singer Страницы: 72

Бренд: Smoke Factory Страницы: 16

Бренд: Uchida Yoko Страницы: 25

Бренд: AIRBLAST Страницы: 43

WaterFuls WR1000EX

Бренд: Innovative Concepts in Entertainment Страницы: 17

Бренд: Singer Страницы: 33

Бренд: JUKI Страницы: 2

Бренд: JUKI Страницы: 8

Бренд: JUKI Страницы: 10

Бренд: JUKI Страницы: 76

Бренд: Bosch Страницы: 24

Бренд: Brother Страницы: 116

Бренд: Brother Страницы: 211

Бренд: Brother Страницы: 124

Бренд: Brother Страницы: 124

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды