Autel MaxiDAS DS808TS Скачать руководство пользователя страница 138 | Manualshive

Страница: 138 / 167

Autel MaxiDAS DS808TS Скачать руководство пользователя страница 138

131

11

Update

This chapter describes the update operation for both the DS808TS tablet and
the MaxiVCI Mini. The software and firmware updates of the tablet can be
completed on the tablet via the Internet, while the updates for MaxiVCI Mini
can be completed either by connecting to a tablet or by connecting with a PC.

Display Tablet Update

The Update application on the tablet downloads the latest released software.
The  updates  improve  the  MaxiDAS  applications’  capabilities,  typically  by
adding  new  tests,  new  vehicle  coverage  and/or  by  adding  enhanced
database applications.

Software Update

When connected to Internet, the tablet automatically searches for available
updates.  Updates  can  be  downloaded  and  installed  on  the  device.  This
section  describes  update  procedures  in  the  MaxiDAS  system.  When  the
Notifications  Center  function  is  enabled  in  the  Settings  application  (See

Notification Center

page 126 for details), a notification message will display

when updates are available.

Figure 11-1

Sample Update Screen

«
...
136
137
138
139
140
...
»

Содержание MaxiDAS DS808TS








































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды