manualshive.com logo in svg

AUTEC Dynamic Series, Руководство пользователя

Поделиться
Скачать
AUTEC Dynamic Series Скачать руководство пользователя страница 27

Working

AUTEC

 Dynamic Series

LIDYNE00-02.fm

Part A: Description, warnings and instructions

A - 21

ENG

6.6 Low Power function

The LOW POWER function allows transmission at a lower power than the nomi-
nal power (see paragraph 1.1) and reduces the radio remote control working
range.
This function aims at:
- making it easier to work with several systems in the same working environ-

ment (i.e.: many working machines in the same working area)

- extending the battery run-time.

This function is established by the machine manufacturer (see technical data
sheet).

6.7 Cable control

The wire control is used:
- in particular working conditions, established by the machine manufacturer
- when it is not possible to build a radio link between the radio remote control

units

- when working in environments where using radio frequencies is not allowed or

is dangerous

- when a fully charged battery is not available.

When using the wire control, it is not possible to eliminate the electric
shock hazard when working near in-ground or overhead high voltage elec-
trical cables.

DISPLAY pushbutton (if the transmitting unit has a display)

This pushbutton is used to:
- activate the display lighting, if it is off
- cyclically scroll the information on the display in two different

modes:
- manual: the lines scroll up each time the pushbutton is

pressed

- automatic: when the DISPLAY pushbutton is pressed for

3 seconds, the lines scroll automatically. If the DISPLAY
pushbutton is pressed another time, it switches back to
manual mode.

It is not possible to scroll the lines if icons only are displayed.
The display lighting stays on for a time set by the machine man-
ufacturer.

Содержание Dynamic Series





































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды