Power Output
60 Watts RMS
Maximum Load
170 Ohms @ 100 Volts
Power Bandwidth
60Hz - 15kHz <0.5% THD
Frequency Response
60Hz - 15kHz (± 3dB)
Total Harmonic Distortion
0.5% @ 1kHz rated power
Signal To Noise Ratio
-72dB with all controls at their centre position
Tone Controls
Bass @ 100Hz: Boost +12dB, Cut -12dB; Treble @ 10kHz: Boost +9dB, Cut -9dB
Inputs
Six mic/aux universal inputs with XLR female mic sockets and dual RCA sockets.
TRS (6.35mm) Jack Insert point.
Input Sensitivity
Mic: 0.6mV @ 200 Ohms all inputs; Aux Inputs 1 - 5: 40mV @ 47K Ohms;
Aux Input 6: 200mV @ 47K Ohms (for CD player or similar high level input)
Insert Point
600mV in/out
Outputs
Speaker: 100, 70 Volts, 8 Ohms; Line: Balanced 700mV @ 10K Ohm;
Tape: 350mV @ 10K Ohms
Phantom Power
15V DC on all mic channels. Internal on/off switch
Controls
6 Input channel gain controls, 1 Bass control, 1 Treble control,
1 Master gain control, 1 Power on/off switch
Indicators
LED Level VU, Power ”on“ LED
Power Source
AC: 240V - 50Hz, 110V - 60Hz (special) 3 pin IEC Connector; DC: 24 Volts
Power Consumption
120 Watts
Protection
AC and DC fuses
Dimensions/Weight
88mm H x 480mm W x 330mm D (Chassis Dimensions Only). 12kg
Tone Generators
Optional four tone module ATC5488
Muting
Optional TX3010 or TX3014 muting modules
Engineered and Distributed By AUDIO TELEX COMMUNICATIONS PTY LTD (
ABN 78 001 345 482
), 149 Beaconsfield Street, Silverwater, Sydney, NSW, 2128 Australia
NSW Tel: (02) 9647 1411 Fax: (02) 9648 3698 VIC Tel: (03) 9890 7477 Fax: (03) 9890 7977 QLD Tel: (07) 3852 1312 Fax: (07) 3252 1237 WA Tel: (08) 9228 4222 Fax: (08) 9228 4233
TAS Tel: (03) 6228 6373 Fax: (03) 6278 1063 SA Tel: (08) 8352 4444 Fax: (08) 8352 4488 Export Enquiries: [email protected]
Website: www.australianmonitor.com.au
ARCHITECTURAL AND ENGINEERING SPECIFICATIONS
The mixer amplifier shall have six universal inputs, each with a balanced microphone with XLR female
socket, and dual RCA line/auxiliary sockets. Auxiliary inputs 1 - 5 shall have a sensitivity of 40 while input
6 shall have a sensitivity of 200mV to accommodate a CD or other high level input.
The master section shall include one master volume control, two EQ controls, one with 12dB of boost
and cut at 100Hz and the other with 9dB of boost and cut at 10kHz. A power on/off switch with blue
“on“ LED and an LED display Vu graduated from +21dB to -3dB shall form part of this section. The
amplifier chassis shall be solidly constructed, suitable for rack mounting in a standard 19” width rack
without the need for additional rack mounting accessories.
Speaker outputs will be transformer isolated and comprise, 100 volts, 70 volt, & 8 ohms. The amplifier
must be capable of delivering 60 watts RMS at 100 volts into a 170 ohm inductive load from mains or
24V DC, with less than 0.5% distortion at 1kHz and with system hum and noise of less than -72dB.
The amplifier shall be an Australian Monitor Installation Series model SA60.