AUSTRALIAN MONITOR HS120P Скачать руководство пользователя страница 5 | Manualshive

Страница: 5 / 28

AUSTRALIAN MONITOR HS120P Скачать руководство пользователя страница 5

PAGE 5

HSP SERIES INSTALLATION AND OPERATION MANUAL

CONTROLS, CONNECTORS & INDICATORS

FRONT PANEL

HSP 1 Channel 1RU shown in above example.

1

USB Communications Port

Plug in the supplied USB Type A to Mini Type B connector into this port to communicate with the amplifier from the PC software application. The PC software application,
downloadable from the Australian Monitor website, allows for real time monitoring of the amplifier inputs and outputs. The PC software application is also used to
configure the DSP functionality to cater for the installation environment.

Consult the Software Control Over USB setup section of this manual for further details of this control.

2

LED Indicators

Status Indicator

This blue LED indicates various states of the amplifier.

LED

MEANING

INDICATION

Blue On

Normal Operation LED solid on. Indicates that device is powered and that no faults exist.

Blue Slow Flash

Standby Mode

Flash LED: On for 50ms, Off for 4s

Blue Flash

Error Mode

LED Off for 2s followed by a flash count of the error code, On for 300ms, Off for 300ms. Multiple errors will be indicated in
consecutive error sequences. Refer to the Fault Finding section of this manual to fix any errors displayed.

See the

Fault Finding

section of this manual to fix any errors displayed.

Protect Indicator

The following table indicates the meaning of each protection mode:

LED

Meaning

Yellow flashing

Amplifier temperature warm

Yellow on

Amplifier temperature hot

Red flashing

Amplifier over temperature*

Red on

Amplifier protect

See the

Fault Finding

section of this manual to fix any errors displayed.

* In the advent of a thermal overload, the internal operating temperature

of the amplifier has exceeded a safe level of operation. The fan will
continue to run and once the amplifier has cooled it will return to
normal operation.

Signal LED

The following table indicates the meaning of the signal LED

LED

Meaning

Green flashing

Audio signal mute

Green on

Audio signal present

Output Clip indicator

A red LED will illuminate when output signal clipping occurs.

3

Power Switch

Press the switch to the up position to power the unit on. At start-up (turn-on),
the input to the amplifier is muted for approximately two seconds.

1

2

3

Front panel

«
...
3
4
5
6
7
...
»

Содержание HS120P





























Отзывы:

Нет отзывов