manualshive.com logo in svg

AUSTRALIAN MONITOR AM1200, Руководство по эксплуатации, Страница: 15 / 20

Поделиться
Скачать
AUSTRALIAN MONITOR AM1200 Скачать руководство пользователя страница 15

Bridge Mode  15

5. Bridge Mode

The term BRIDGE is used when two independent
amplifier channels are used to drive the same load. The
load is in series (a bridge) between the two amplifier
channels.

Channel A is used as the "dominant" channel and its
output is in phase with the input signal, and channel
B has its phase reversed so it is exactly 180

0

 out of

phase with the input signal.

As two amplifiers with a phase difference of 180

0

 are

now driving the load you will now have double the
voltage into the load. This means you will now have four
times the power into that load. The output can now be
considered as an active balanced output.

A common use of an amplifier in BRIDGE mode is for
driving 70 volt & 100 volt distribution lines. In BRIDGE
mode, The 

AM1200

 can produce over 70 volts with line

impedances greater than 8 ohms and over 80 volts with
line impedances greater than 16 ohms.

Equally the units can be used in bridge mode to provide
the correct voltage/power requirements for an applica-
ble load.

As shown in Figure 6, there are three steps in setting

Figure 6   Bridge Mode Speaker Connection

up your amplifier for running it in BRIDGE mode.
Whilst the amplifier is off,
1. Connect the signal source to the Channel-A (or D)

female input XLR. The Channel-A (or D) attenuator
becomes the level control for both channels.

2. Engage the “push to bridge” switch.

3. Connect your load between the red binding post

output terminals, where the positive side of the
load is connected to the channel A (or D) output
(marked BRIDGE+) and the negative side of the
load goes to the channel B (or C) output (marked
BRIDGE

-

). There are no further connections re-

quired.

You can also source the output from the Channel-A (or
D) SPEAKON output connector where Channel-A (or
D) will be on the pin marked 1+ and Channel-B (or C)
will be on the pin marked 2+.

NOTE: You should check after market manufactured
Speakon interconnecting speaker leads before con-
necting them to your amplifier. Some leads are manu-
factured for specific purposes, or specific use, and
may have pins shorted inside the connector. Any
speakon lead with shorted pins will obviously short the
output of your amplifier (either to ground, or output to
output - be careful).

Содержание AM1200





















Отзывы:

Нет отзывов