10.0 Specifications
Heart Rate Chronograph Mode
Chronograph
!
Resolution: 1/100 second
!
Measuring Range: 9 hours 59 minutes 59.99
seconds
!
Maximum: 25 Laps
Heart Rate Zone Timer
!
Resolution: 1 second
!
Measuring Range: 9 hours 59 minutes 59
seconds
Calorie Consumption
!
Range: 0 to 9999 kilo-calorie
Fat Burnt
!
Range: 0 to 9999 gram
Heart Rate Measurement
!
Buttonless Finger Touch Measurement
!
Range: 40 to 200 bpm
!
Heart Rate Zone Alert
Current Time Mode
!
Time System: am, pm, hour, minute, second
!
Time Format: 12-hour or 24-hour format
!
Calendar: date and day of week display
(Auto-Calendar function for day of week and
leap year)
Daily Alarm
!
Daily alarm and hourly chime
!
Alarm Sound: 1 minute
Timer Mode
!
Resolution: 1 second
!
Measuring Range: 9 hours 59 minutes 59
seconds
!
Timer sounds: Last 10 seconds will beep each
second and continue for a further 15 seconds.
Memory Mode
!
Lap Time Recall
!
Total Time Recall
Back Light
!
Back Light Type: Electro-Luminescent (EL)
back light
9.0 Potential Causes for
NO Heart Rate Reading or Long Response Time
1) Cause: Dry Skin.
Solution: Apply conductive gel or saliva thoroughly to finger and wrist. Even water
will help if conductive gel is not available.
2) Cause: Not firmly with user’s skin.
Solution: Make sure the Watch is placed securely on wrist.
3) Cause: Muscle tremors caused by holding too hard.
Solution: Make sure the Watch is placed securely on wrist.
4) Cause: Dead skin on wrist, finger or chest.
Solution: Usually rubbing your skin with a towel will help.
5)Cause: A thin layer of body grease insulate the ECG signal which prevents the
Chest Strap or Watch from picking up one's ECG.
Solution: Wipe wrist and the back of the watch with a tissue or soft towel.
6) Cause: Hairy skin.
Solution: Apply conductive gel to wrist.
7) Cause: Irregular heartbeats.
Solution: N/A It is difficult to consistently pick up a reading for those with irregular
heart beats. Inconsistent response times are expected for those with arrhythmia.
8) Cause: Battery Low.
Solution: It might be due to the battery level of the watch is low. Replace the battery
and try again.
To Use the Timer Mode
!
Once a target time has been set (for
example 3 hours), press the [S/S] button
once to start the countdown. The
countdown time will be displayed
continuously throughout the countdown.
!
To stop counting, press the [S/S] button
once.
To Reload the Timer
!
Hold the [R] button to reload the timer to
the preset target time when the counting is
stopped.
!
To start the counting at a target time, set a
new value for the pre-defined target time.
Check the previous chapter 8.0 for more
detail on how to set the Target Time.
Timer Alarm Sound
!
When the timer reaches the last 10
seconds, the watch will beep once for each
second left. When it hits zero, the watch
will beep for about 15 seconds
!
You can stop the beeping by pressing any
button.
counting
stop
counting
Timer Mode
(Counting)
Timer Mode
(Stop Counting)
Timer Mode
(Finish Counting)
Timer Mode
(Timer initialized)
[S/S]
[S/S]
Hold [R]
4:59'59"
Current Time
Hold [R]
Pre-defined
Target Time
beeps
beeps
beeps
8.1 Timer Mode -
Using Timer
Note
:
This diagram illustrates the flow
among different functional displays
only, hence, these displays DO
NOT conform to fact in all
instances.
www.aussiefitsport.com.au
