9
Download / control through
the AOne App
Trim
Pot
• Installation must be carried out in accordance with the latest edition of the
Wiring Rules by a qualified/competent electrician.
• Hereby, Aurora Limited declares that the radio equipment type
AU-A1ZB2WDM is in compliance with Directive 2014/53/EU. The full text of the
EU declaration of conformity is available at the following internet address:
www.auroralighting.com/ProductDetail/AU-A1ZB2WDM
5
1:1
2
Document Version: AU-A1ZB2WDM_1P_2P_V1_18
www.auroralighting.com
USING THE APP TO CONNECT THE SMART ROTARY
DIMMER TO THE HUB
1. Download the AOne App from the App Store.
2. Follow instructions on the AOne App to send the hub into pairing mode and
pair your devices (further details below).
3. The dimmer will enter pairing mode once it has power. To re-pair the dimmer
manually, push and hold the knob for 6 seconds.
The connected load, and the red LED indicator behind the dimmer knob will flash
twice to indicate it has entered pairing mode.
The connected load, and the red LED indicator behind the dimmer knob will flash a
third time to indicate that it has paired with the hub.
The dimmer can then be controlled using the AOne App.
Minimum depth of backbox must be 25mm
If you wish to adjust the minimum dimming level do not
fully screw the dimmer into the backbox
If you have purchased a
module only, skip to step 5
Optional:
If you have purcahsed a module
only and/or wish to use your existing
faceplate, remove the faceplate that comes
installed on the dimmer and follow the
existing faceplate install guide:
Before starting work; Take a photo of
existing wiring and terminals.
MODEL
AU-A1ZB2WDM,
AU-A1ZB2WDM1P, AU-A1ZB2WDM2P
VOLTAGE (V)
220-240V AC
RESISTIVE MAX LOAD
250W
INPUT CURRENT
1.04A
OUTPUT VOLTAGE
220-240V 50Hz AC
AMBIENT TEMPERATURE LIMITS
-20°C~+50°C
IP RATING
IP20
PROTOCOL
Zigbee 3.0
CONDUCTOR TYPE & SIZE
Twin and Earth 0.75~2.5 mm
2
(UK)
FREQUENCY BAND
2400 MHz - 2483.5 MHz
MAX OUTPUT RF POWER
13 dBm/mW
INSULATING MATERIALS
PTI 175
GLOW-WIRE TEMPERATURE
650°C
PROTECTIVE DEVICE
1A fuse on output
RATED IMPULSE WITHSTAND VOLTAGE
1.5 KV
RATED POWER
LED: 250W | HV Halogen: 250W, |
Electronic Transformer: 250W
MIN. LOAD OF LIGHTING (SUBJECT TO
DEVICE POWER FACTOR < 0.9)
Typical LED 10W (Depending on the
input characteristics of the load)
DIMMING RANGE
0-100%
ADDITIONAL FEATURES
Trailing edge dimming mode
1
10
8
Minimum Dimming Adjustment
To adjust the minimum dimming level of the connected load(s):
• Switch the load on.
• Turn on the MASTER dimmer fully anti-clockwise. The load
may turn off or possibly flicker.
• With a terminal screwdriver adjust the Trim Pot to set the
minimum brightness of the load. Clockwise to increase the
brightness, anti-clockwise to reduce the brightness.
• Tighten faceplate screws and fit faceplate when the
Minimum Dimming Adjustment is complete.
KEEP FINGERS AND TOOLS CLEAR OF WIRES & WIRING
TERMINALS WHILST POWER IS ON
7
4
In order to wire the dimmer, please check
the back page of this install guide and
follow the appropriate wiring diagram.
6A
6B
ONE WAY WIRING
TWO WAY WIRING
3
Master mode
Slave mode
IMPORTANT INFORMATION:
• Do NOT operate the master/slave
switch when power to the product is on
• Read and remove the warning label to
access the master/slave switch
• The blue LED backlight may be
switched off in the app if required
