manualshive.com logo in svg

AUMA SVM 05.1, Руководство по эксплуатации

Поделиться
Скачать
AUMA SVM 05.1 Скачать руководство пользователя страница 24

Activate operation mode Remote by means of local controls:

→

If indication light [4] is blinking in blue: Hold down push button [2] for approx. 3

seconds until the blue indication light goes out.

➥

Now, the actuator can be remote-controlled via fieldbus.

Change-over between OPEN - CLOSE control and setpoint control:

For actuators equipped with a positioner, it is possible to select between OPEN
CLOSE control (Fieldbus REMOTE/Fieldbus CLOSE ) and setpoint control
(Fieldbus SETPOINT).

EMERGENCY operation:

●

An EMERGENCY operation is initiated by the Fieldbus EMERGENCY command
bit.

●

The actuator moves to a predefined EMERGENCY position (i.e. end position
OPEN or end position CLOSED).

●

During EMERGENCY operation, the actuator does not react to other operation
commands such as Fieldbus/OPEN/Fieldbus/CLOSE or Fieldbus SETPOINT.

24

 SVM 05.1 – SVM 07.5 / SVMR 05.1 – SVMR 07.5

Operation

 Modbus RTU

Содержание SVM 05.1

























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды