AUMA SA 07.2-UW Скачать руководство пользователя

Страница: 32 / 76

Table 23: Important push button functions for menu navigation

Functions

Navigation sup-
port on display

Push buttons

Change screen/selection

Up ▲

[1]

Change values

Enter figures from 0 to 9

Change screen/selection

Down ▼

[2]

Change values

Enter figures from 0 to 9

Confirm selection

[3]

Save

Enter <Edit> menu

Edit

Display more details

Details

Enter Main menu

Setup

[4] C

Cancel process

Esc

Return to previous display

Backlight

●

The display is illuminated in white during normal operation. It is illuminated in
red in case of a fault.

●

The screen illumination is brighter when operating a push button. If no push
button is operated for 60 seconds, the display will become dim again.

6.2.1.

Menu layout and navigation

Groups

The indications on the display are divided into 3 groups:

Figure 29: Groups

[1]

Start menu

[2]

Status menu

[3]

Main menu

Status menu and main menu are marked with an ID.

Figure 30: Marking with ID

ID starts with

= status menu

ID starts with

= main menu

Group selection

It is possible to select between status menu

and main menu

For this, set selector switch to 0 (OFF), hold down push button C for approx. 2
seconds until a screen containing the ID

M...

appears.

Figure 31: Select menu groups

You return to the status menu if:

SA 07.2-UW – SA 16.2-UW / SAR 07.2-UW – SAR 16.2-UW Control unit: electronic (MWG)

Operation

AC 01.2 Non-Intrusive Profinet

Содержание SA 07.2-UW













































































Результаты поиска

Содержание SA 07.2-UW

Отзывы:

Похожие инструкции для SA 07.2-UW

Бренды по названию

Популярные бренды

AUMA SA 07.2-UW, Руководство по эксплуатации

Результаты поиска

Содержание SA 07.2-UW

Отзывы:

Похожие инструкции для SA 07.2-UW

Бренды по названию

Популярные бренды