manualshive.com logo in svg

AUMA PROFOX PF-M100, Руководство по эксплуатации

Поделиться
Скачать
AUMA PROFOX PF-M100 Скачать руководство пользователя страница 21

7.

Connect power supply.

If commissioning is directly performed following electrical connection: Do not
close cover!

6.5.

Terminal compartment: close

Figure 18: Terminal compartment: close

[1]

Cover

[2]

Screws

[3]

Cable entry

[4]

Blanking plug

[5]

Cable gland (not included in scope of delivery)

Short-circuit due to pinching of cables!

Risk of electric shock and functional failures.

→

Carefully assemble cover to avoid pinching the cables.

1.

Clean sealing faces of cover [1] and housing.

2.

Fit cover [1] and fasten screws [2] evenly crosswise.

6.6.

External earth connection (option)

Hazardous voltage due to insulating impact of powder coating!

Risk of electric shock.

→

Strip powder from actuator surface (file down).

→

Connect all protective earth conductors.

→

Connect PE connection to external protective earth conductor of connection
cable.

→

Power the device only once the protective earth conductor has been connected.

21

PROFOX / PF-M25 – PF-M100 
Profibus DP 

Electrical connection

Содержание PROFOX PF-M100

















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды