AUMA ACV 01.2 Скачать руководство пользователя страница 121 | Manualshive

Страница: 121 / 168

background image

→

Select “– – / –N/A–” during operation and confirm via

Ok

(push button ). The

actuator stops in its current position.

12.1.7.

Operate to position from Remote

For direct operation to position from remote, make sure that selector switch position
Remote control (REMOTE) is selected.

Approach position via fieldbus command

If fieldbus interface control has been selected, the operation command for direct
position approach is performed via a fieldbus command.

Example:

Fieldbus command

Fieldb. interm. pos. 1

:

●

Fieldb. interm. pos. 1

= 0 (low active) = no operation command

●

Fieldb. interm. pos. 1

= 1 = intermediate position 1 is approached selecting the

shortest path

The commands are described in the Manual (Device integration fieldbus).

If the operation commands for direct position approach are not issued via fieldbus
command but are to be transmitted using a binary signal, (e.g. + 24 V DC) via
<Additional inputs> or via an additional <Parallel interface>, digital inputs must be
provided and configured accordingly.

Operation to position via digital inputs

An input (DIN) must be configured for each position (valve port).

Configuration of digital inputs

Required user level:

Specialist (4)

or higher.

Device configuration M0053

I/O interface M0139

Digital inputs M0116

Example

DIN4 input to operate to position 1 selecting the shortest path:

Parameters:

Signal DIN 4 M0118

=

Intermediate pos. 1

Operation behaviour for input control

Setting values for digital inputs (DIN)

Operation to defined position while selecting the
shortest path

Intermediate pos. 1

to

Intermediate pos. 16

Operation to defined position in clockwise direction

MPV: CW Position 1

to

MPV: CW Position 10

Operation to defined position in counterclockwise
direction

MPV: CCW Position 1

to

MPV: CCW Position 10

Actuator operates in clockwise direction (without
stop at any position).

MPV DriveCW

Actuator operation in counterclockwise direction
(without stop at any position).

MPV DriveCCW

Command “Next position”

Required user level:

Specialist (4)

or higher.

A digital input is used to select the desired operation to the next port including the
direction of operation. Thus, up to 16 ports can be approached in both directions,
even without fieldbus connection with only 2 inputs.

Device configuration M0053

I/O interface M0139

Digital inputs M0116

Example

Parameter

Signal DIN 1 M0117

:

●

Next position CW

= clockwise

●

Next position CCW

= counterclockwise

121

Actuator controls
ACV 01.2/ACVExC 01.2 Profibus DP

Product variants

«
...
119
120
121
122
123
...
»

Содержание ACV 01.2









































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ACV 01.2

Бренд: ZIMO Страницы: 38

Бренд: Laird Страницы: 38

Бренд: Laird Страницы: 5

Бренд: S&P Страницы: 12

Бренд: S&C Страницы: 34

Бренд: S&C Страницы: 32

IntelliCap Plus

Бренд: S&C Страницы: 32

Бренд: S&P Страницы: 12

Бренд: S&C Страницы: 35

Бренд: V2 Страницы: 12

NORA-W10 Series

Бренд: u-blox Страницы: 56

Бренд: z21 Страницы: 2

NOVASTAT EL DIGITAL

Бренд: Taconova Страницы: 7

Бренд: GEA Страницы: 13

CIATControl OPC Server

Бренд: CIAT Страницы: 32

EnviroLift EW0820S090

Бренд: Challenger Lifts Страницы: 23

Бренд: Danfoss Страницы: 8

Infi 90 IMAOM01

Бренд: Bailey Страницы: 44

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды