manualshive.com logo in svg

AUMA ACExC 01.2 Intrusive, Руководство по эксплуатации

Поделиться
Скачать
AUMA ACExC 01.2 Intrusive Скачать руководство пользователя страница 22

5.3.3.

Output drive types B/C/D and E

Figure 17: Mounting principle

[1]

Flange multi-turn actuator (e.g. F07)

[2]

Hollow shaft

[3]

Output drive sleeve (illustration examples)

[4]

Gearbox/valve shaft

Short description

Connection between hollow shaft and valve or gearbox via output drive sleeve fixed
to the hollow shaft of the multi-turn actuator via retaining ring.

When exchanging the output drive sleeve, later retrofitting to a different output drive
type is possible

●

Output drive type B/E:
Output drive sleeve with bore according to DIN 3210

●

Output drive types B1/B3:
Output drive sleeve with bore according to EN ISO 5210

●

Output drive types B2/B4:
Output drive sleeve with bore according to customer order
B4 including special bores like bores without keyway, square bore, hexagon
bore, internal splines

●

Output drive type C:
Output drive sleeve with dog coupling according to EN ISO 5210 or DIN 3338

●

Output drive type D:
Shaft end with key according to EN ISO 5210 or DIN 3210

Information

Spigot at valve flanges should be loose fit.

22

SAEx 07.2 – SAEx 16.2/SAREx 07.2 – SAREx 16.2 Control unit - electromechanical

Assembly

ACExC 01.2 Intrusive Profinet

Содержание ACExC 01.2 Intrusive









































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды