Auerswald COMpact 5000 Скачать руководство пользователя страница 90 | Manualshive

Страница: 90 / 932

background image

90

COMpact 5000/R - Firmware V6.6A - Installation, Operation and Configuration V05 03/2016

Installation and Commissioning

ISDN End Devices
Available Bus Variants for the Installation of an Internal S

0

Bus

Note:

If the end device is placed a larger distance away from the PBX, the

cable and the wall sockets must be permanently installed.

•

For connecting multiple end devices on one internal S

0

port: one ISDN multiplug

Note:

The Auerswald ISDN Multiplug is available for this wiring type as

optional accessories in specialised stores.

Depending on the number of the end devices, proceed as follows.

•

Single end device: Connect the end device to the RJ-45 socket on the S

0

port.

•

Multiple end devices: Connect the ISDN Multiplug to the RJ-45 socket that belongs to
the internal S

0

port and connect the end devices to the ISDN Multiplug.

Further steps:

•

To finish commissioning, you need to set up an internal number for the end device in the
configuration manager.

Available Bus Variants for the Installation of an Internal S

0

Bus

Several bus variants can be used for the installation of cables and wall sockets at the internal
S

0

port.

Short Passive Bus in One Direction

The short passive bus with up to 12 wall sockets is suited for the connection of several end
devices at medium distances. It supports cable lengths of up to 150 m. The terminators have
to be switched on at the internal S

0

port. See the following figure.

«
...
88
89
90
91
92
...
»

Содержание COMpact 5000





































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для COMpact 5000

OpenCom 100 series

Бренд: Aastra Страницы: 2

Бренд: Quadro Страницы: 57

Бренд: Panasonic Страницы: 32

Бренд: SIP Страницы: 46

IP Office 500 V2

Бренд: Avaya Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды