manualshive.com logo in svg

Auerswald COMpact 5000, Руководство по эксплуатации

Операционный мануал для Auerswald COMpact 5000 доступен для бесплатного скачивания на нашем сайте. Подробное описание всех функций и возможностей продукта вы найдете в этом руководстве. Скачайте свой экземпляр прямо сейчас с manualshive.com.

Поделиться
Скачать
background image

COMpact 5000/R - Firmware V6.6A - Installation, Operation and Configuration V05 03/2016

731

Settings

Exchange Line Request

Switching System-wide Automatic Exchange Line Request On/Off

Switching System-wide Automatic Exchange Line Request On/Off

If the system-wide automatic exchange line request ist enabled, the PBX automatically distin-
guishes for each subscriber between internal and external numbers by analysing the digit 
sequence and the adjustment of the dialled phone number with the internal numbering plan.

If the system-wide automatic exchange line request is disabled, the exchange line request type 
can be set separately for each subscriber.

Important:

 After a firmware update from an older firmware version to version 

6.6, the system-wide automatic exchange line request is at first switched off. 
If the system-wide automatic exchange line request is switched on, you must 
note the following for the conversion of the existing telephones.

COMfortel 600: For all phone numbers that are entered in the configuration 
of the telephone (concerns speed dialling keys and telephone book), possibly 
entered exchange line access numbers or ** (initiation of internal numbers in 
the direct exchange line telephone) must be deleted.

COMfortel 1100/1500/2500/2500 AB/2500 VoIP AB: For the call forwarding 
variation „for external numbers“ the exchange line access number preceding 
the destination number must be deleted or omitted.

Proceed as follows:

•

Via the configuration manager

Requirements:

•

Emergency call only with disabled exchange line access number (page 

Public switched 

tel. networks > Emergency calls

)

1. Open the page 

Public switched tel. networks > Exchange line request

.

2. Select or clear the 

System-wide automatic exchange line request

 check box.

Содержание COMpact 5000





































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для COMpact 5000

Panasonic KX-TD816 Specifications preview
KX-TD816
Бренд: Panasonic Страницы: 8
Panasonic KX-HGT100-B Brochure & Specs preview
KX-HGT100-B
Бренд: Panasonic Страницы: 8
Epygi Quadro Quadro 4xa Specifications preview
Quadro Quadro 4xa
Бренд: Epygi Страницы: 2
Auerswald COMpact 4000 Instructions Manual preview
COMpact 4000
Бренд: Auerswald Страницы: 200
Auerswald COMmander 6000 Advanced Information preview
COMmander 6000
Бренд: Auerswald Страницы: 1164

Бренды по названию

Популярные бренды

Загрузить еще бренды