manualshive.com logo in svg

Auerswald COMpact 5000, Руководство по эксплуатации

Операционный мануал для Auerswald COMpact 5000 доступен для бесплатного скачивания на нашем сайте. Подробное описание всех функций и возможностей продукта вы найдете в этом руководстве. Скачайте свой экземпляр прямо сейчас с manualshive.com.

Поделиться
Скачать
background image

COMpact 5000/R - Firmware V6.6A - Installation, Operation and Configuration V05 03/2016

695

Settings

Call Distribution

Configuring Fallback

Configuring Fallback

The fallback function indicates how the PBX deals with calls which could not be transferred or 
rejected via call distribution. Rejecting or special fallback settings are available as fallback 
options.

The following fallback settings can be configured:

•

Only Announcement before Answering: The caller hears the Announcement before 
Answering and then, the connection is interrupted.

•

Fallback phone number and no Announcement before Answering: The call will be ringing 
on the selected internal number.

•

Fallback phone number and Announcement before Answering: 

– immediately

: The call is immediately signaled at the internal number for the fallback. It 

is, thus, signaled in parallel to the announcement before answering.

– after Announcement before Answering

: The call is signalled after the announcement 

before answering to the internal number for fallback and, thus, in parallel to the call 
phase.

Proceed as follows:

•

Separately for configurations

•

Separately for external connections

•

Using the configuration manager

Requirements:

•

Entered external numbers

•

Created internal destinations (subscribers, groups, voice mailboxes or automatic reception)

1. Open the page 

Public switched tel. networks > Call distribution

.

If several configurations (PBX profiles) have been created, these will be available as 
tabs.

2. With several configurations: Click the tab with the desired configuration.

3. In the 

CALL DISTRIBUTION FOR...

 list fields select the connection.

4. Under 

Fallback

, select one of the following options:

Reject

: The caller will hear the busy signal. (Continue with step 8.)

Fallback settings: The caller will be transferred according to the settings.

Содержание COMpact 5000





































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для COMpact 5000

Panasonic KX-TDA50 Programming Manual preview
KX-TDA50
Бренд: Panasonic Страницы: 726
VoLANs VoSS12 Admin Manual preview
VoSS12
Бренд: VoLANs Страницы: 127

Бренды по названию

Популярные бренды

Загрузить еще бренды