Auerswald COMpact 5000 Скачать руководство пользователя | Manualshive

Страница: 506 / 932

background image

506

COMpact 5000/R - Firmware V6.6A - Installation, Operation and Configuration V05 03/2016

Functions

Telephone Book Authorisation
Switching Telephone Book Authorisation for Subscriber On/Off

Telephone Book Authorisation

You can add telephone book authorisation to the exchange line authorisations to add options
for dialling specific phone numbers if restricted exchange line authorisation is in place.

This then enables you to approve specific phone numbers for a dial attempt. With telephone
book authorisation you are permitted to dial all the phone numbers entered in the

Telephone

book version 1

contact group of the address books.

Important:

The telephone book authorisation only becomes effective if no corresponding
exchange line authorisation is present on any of the external connections.

If only the

Internal only, no emergency calls

exchange line authorisation is

present, you cannot make an external call even if you have telephone book
authorisation.

Switching Telephone Book Authorisation for Subscriber On/Off

If the telephone book authorisation is enabled for a subscriber, the subscriber can dial the
phone numbers entered in the contact group

Telephone book version 1

irrespective of his

exchange line authorisation.

Proceed as follows:

•

Separately for subscribers

Note:

If differently configurable functions for private and business calls are

enabled, two different configurations can be created for each subscriber –
one for private calls and one for business calls (see also chapter Functions >
Private (Personalised) Exchange Line Access > Switching Differently Config-
urable Functions for Private and Business Calls On/Off).

•

Separately for configurations

•

For the exchange line transfer function (

Settings > Basic settings > EXCHANGE LINE

CALL TRANSFER > Exchange line settings for the manually switched exchange line
access > Configure special exchange line settings > Configure

)

•

For the Call Through function (

Functions > Call Through > EXCHANGE LINE SETTINGS

> Configure

)

•

Using the configuration manager

«
...
504
505
506
507
508
...
»

Содержание COMpact 5000





































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для COMpact 5000

TC-2000 AK Series

Бренд: CTI Страницы: 65

Бренд: Wahsega Страницы: 8

Бренд: Panasonic Страницы: 204

Бренд: XONTEL Страницы: 118

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды