manualshive.com logo in svg

Auerswald COMpact 5000, Руководство по эксплуатации

Операционный мануал для Auerswald COMpact 5000 доступен для бесплатного скачивания на нашем сайте. Подробное описание всех функций и возможностей продукта вы найдете в этом руководстве. Скачайте свой экземпляр прямо сейчас с manualshive.com.

Поделиться
Скачать
background image

COMpact 5000/R - Firmware V6.6A - Installation, Operation and Configuration V05 03/2016

351

Functions

Call Allowance Account

Configuring Credit for a Call Allowance Account

Call Allowance Account

A call allowance account is a restricted amount of currency units that is configured for each 
telephone. When these units are used up, it becomes no longer possible to make external calls 
on the corresponding telephone until the credit is reset.

Configuring Credit for a Call Allowance Account

In order to carry out charge verification, credit can be added to the individual call allowance 
accounts. As soon as the configured credit is used up, it is no longer possible to make external 
calls on the corresponding telephone until the credit has been increased or reset.

If the remaining amount is used up during a call, the subscriber hears a short attention tone 
repeatedly. Afterwards, the call is disconnected.

Proceed as follows:

•

Separately for subscribers

•

Using the configuration manager

•

Using a character string on the internal telephone (see section Short Reference)

Note:

Some telephone service providers do not transmit charges. If this provider 
type is used (by manual selection) for making calls, a configured call 
allowance account will not apply to the call in question. To avoid this, the 
provider phone numbers in question should be entered as restricted numbers 
and this function should be enabled for every telephone.

If the LCR procedure Soft-LCR 4.0 is used, the charges are calculated based 
on the length of the call and the tariff table set up separately. For this purpose, 
you need to specify a price per minute as well as the length of the charge 
pulse per switching time and provider.

Configuring Credit for a Call Allowance Account

Requirements:

•

External S

0

 port (optional, see chapter Important Information > Product Details > Basic 

Assembly and Extensions)

Содержание COMpact 5000





































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для COMpact 5000

SpectraLink Link 3000 MCU Installation Manual preview
Link 3000 MCU
Бренд: SpectraLink Страницы: 54
Well mPBX-100 User Manual preview
mPBX-100
Бренд: Well Страницы: 140
Planet IPX-2000v2 Quick Start Manual preview
IPX-2000v2
Бренд: Planet Страницы: 5
Planet Internet Telephony PBX System IPX-300 Series Quick Installation Manual preview
Internet Telephony PBX System IPX-300 Series
Бренд: Planet Страницы: 20
WELLTECH ePBX40 User Manual preview
ePBX40
Бренд: WELLTECH Страницы: 130

Бренды по названию

Популярные бренды

Загрузить еще бренды